Installing The Koos Isize R1 With The Comfy Base In The Car - JANE CONCORD KOOS Mode D'emploi

Carry handle, with 3 positions:
Position 1: Resting. In this position the handle lies flat against the frame.
This position is free, it does not lock.
Position 2: CARRYING. Making it easier to carry.
Position 3: CAR. Anti-rotation position for use in the car.
To change the position, press both buttons 2 .d and turn the handle
to the required position. To move it from the resting position it is not
necessary to press the buttons, simple move the handle.
2
3
1
Adjust the height of the harness by simply pressing a button. Avoids
the inconvenience of having to remove and then fit the straps again
when you need to change the height of the belts.
Removable and washable upholstery.
24
EN
F. INSTALLING THE KOOS iSIZE R1 WITH THE
COMFY Base IN THE CAR
INSTALLING THE COMFY Base IN YOUR CAR
Not all systems are the same, therefore we advise you to test your
COMFY Base in the car where it is going to be installed. To install the
platform, read your vehicle instruction manual, it will tell you which
seats are compatible with the platform. The COMFY Base is compatible
with the ISOfix category D.
The anti-rotation leg (1) is an important safety feature, fit it correctly so
it is supported by the floor of the vehicle. If the leg support surface is
not the actual vehicle chassis (luggage compartment for example) do
not install the platform on this seat. To do this, follow the steps below:
Position the base on the seat with the anti-rotation leg (1) and the
fastening bar (9) unfolded. Extend the leg with the help of the upper
adjustment button (5a), until the window indicator shows OK and the
button changes to green. 1 .a
Extract the ISOfix anchors (2) by turning the handle (4) on the side of
the platform. 1 .b
Guide both anchors (2) towards the ISOfix connectors of your vehicle
and press until both sides are locked. Two green signals on the top
part of the ISOfix (2) will show you that they are correctly anchored.
1
If one or both of the signals are red, repeat this step. .c
Adjust the height of the leg (1) so that it rests on the floor of the
vehicle, the indicator on the base of the leg (9) and the indicator on the
leg adjustment button (5b) will turn green. 1 .d
The COMFY base can be reclined to improve the angle of rest for the
baby. Turn the handwheel (3) to adjust the angle. 1 .e
INSTALLING THE KOOS iSIZE R1 ON THE COMFY Base
Position the baby carrier so that it is fastened with the Pro-Fix anchors
2
intended for the KOOS iSIZE R1 (7). .a
Check that both sides are securely anchored, your KOOS iSIZE R1
will click when it is correctly locked in place and a green strip will be
2
displayed on the Pro-Fix lever (found on the handle dial). .b
Set the KOOS iSIZE R1 handle to the CAR position, make sure that it
is locked in place, and that the whole car symbol is displayed.
To do this, simultaneously press the release buttons found on
both sides of the handle, and set it to the position that is furthest
forward. 2 .d
Turn the handle (5) so the whole group is firmly pressed against the
vehicle backrest. 2 .e
WARNING: Your COMFY Base can be used with two different baby ca-
!
rrier models, make sure you insert the Pro-fix of your KOOS iSIZE R1
into the correct position for this model, you will find the instructions on
the platform. Once anchored, the exterior surface of the safety seat
backrest should be touching the fastening bar (9) 2
DETACHING THE KOOS iSIZE R1 FROM THE COMFY Base
Set the KOOS iSIZE R1 handle to the Carrying position.
Pull the release levers on both sides of the handle to release the
Pro-fix anchors and lift the baby carrier up. 2 .g
To remove the platform:
2 .c
Release the ISOfix anchors by pressing the buttons (4), the signal on
the ISOfix anchor buttons will turn red. 2 .h
The ISOfix anchors can be hidden inside the platform. (5)
.f
2
.i
EN 25