Skil 7338 Notice Originale page 7

APPLICATION ADVICE
•
Move the tool in straight movements in line with the grain
- for sanding bare wood surfaces
- for extra fine finishing
•
Never use the same sanding sheet for wood and metal
• Recommended sanding sheet grits:
- for removing paint and for sanding of extremely rough
wood use coarse grit sizes (40, 60)
- for sanding of rough or plain wood use medium grit
sizes (80, 100, 120)
- for smoothing of wood and surfaces with old paint as
well as for finishing of bare wood use fine grit sizes
(180, 240, 320)
! always test out first on a piece of scrap material
Use different grit sizes when the working surface is
•
rough:
- start sanding with coarse or medium grit
- finish with fine grit
• For more tips see www.skil.com
MAINTENANCE / SERVICE
•
This tool is not intended for professional use
•
Always keep tool and cord clean (especially ventilation
slots C 2 )
- remove adhering sanding dust with a brush
! disconnect the plug before cleaning
If the tool should fail despite the care taken in
•
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
ENVIRONMENT
•
Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 7 will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
•
We declare under our sole responsibility that the product
described under "Technical data" is in conformity with
the following standards or standardization documents:
EN 60745, EN 61000, EN 55014, in accordance with the
provisions of the directives 2004/108/EC, 2006/42/EC,
2011/65/EU
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
Marijn van der Hoofden
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
02.07.2014
16.05.2013
NOISE/VIBRATION
•
Measured in accordance with EN 60745 the sound
pressure level of this tool is 85 dB(A) and the sound
power level 96 dB(A) (standard deviation: 3 dB), and the
vibration 8.4 m/s² (hand-arm method; uncertainty
K = 1.5 m/s²)
•
The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Ponceuse vibrante
INTRODUCTION
•
Cet outil sert au ponçage et au polissage à sec du bois,
des surfaces peintes, du plastique et du mastic
•
Cet outil n'est conçu pour un usage professionnel
•
Lisez et conservez ce manuel d'instruction 3
CARACTERISTIQUES TECHNIQUES 1
ELEMENTS DE L'OUTIL 2
Interrupteur marche/arrêt
A
B
Connexion pour aspirateur
C
Fentes de ventilation
SECURITE
INSTRUCTIONS GENERALES DE SECURITE
ATTENTION! Lisez tous les avertissements de
sécurité et toutes les instructions. Ne pas suivre les
avertissements et instructions peut entraîner un choc
électrique, un incendie et/ou de graves blessures sur
les personnes. Conservez tous les avertissements
et toutes les instructions pour pouvoir s'y reporter
7
Olaf Dijkgraaf
Approvals Manager
7338