Connect To Water Line; Connect To Refrigerator - Jennair KBSD706MPS Manuel D'utilisation

Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.

Connect to Water Line

Parts Needed
� Minimum 7 ft (2.13 m) flexible, codes-approved water supply
line.
Style 1 – Shutoff Valve Connection
NOTE: If your water line connection does not look like Style 1, see
"Style 2 — Copper Line Connection."
1. Unplug refrigerator or disconnect power supply.
IMPORTANT:
� There is not enough clearance to achieve a flush
installation if a water shutoff valve is located in the wall
behind the refrigerator. The water shutoff should be
located in the base cabinet on either side of the
refrigerator.
� Before attaching the tubing to shutoff valve, flush the main
water supply line to remove particles and air in the water
line. Allow enough flow so that water becomes clear.
Flushing the water line may help avoid filters and/or water
valves from becoming clogged.
2. Connect the flexible, codes-approved water supply line to the
water shutoff valve by threading the provided nut onto the
shutoff valve as shown.
A.
Bulb
B.
Nut
C.
Water tubing
3. Place the end of the tubing into a bucket, and turn shutoff
valve ON.
4. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Style 2 — Copper Line Connection
NOTE: If there is a water supply line that meets the specifications
in "Water Supply Requirements," proceed to "Connecting to
Refrigerator." If not, use the following instructions to connect to the
household cold water supply.
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a 1/2" to 1 1 / " (1.3 cm to 3.18 cm) vertical cold water
4
pipe near the refrigerator.
IMPORTANT:
� Make sure it is a cold water pipe.
� Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and keep normal sediment from collecting in the
valve.
4. Determine the length of copper tubing you need. Measure
from the connection on the refrigerator to the water pipe. Add
7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D.
(outside diameter) copper tubing. Be sure both ends of copper
tubing are cut square.
5. Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold
water pipe you have selected.
a.
Cold water pipe
b.
Pipe clamp
c.
Copper tubing
d.
Compression nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
IMPORTANT: Before attaching the tubing to shutoff valve,
flush the main water supply line to remove particles and air in
the water line. Allow enough flow so that water becomes clear.
Flushing the water line may help avoid filters and/or water
valves from becoming clogged.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten the
clamp or the sleeve. This will crush the copper tubing.
8. Turn off the shutoff valve on the water pipe. Coil the copper
tubing.
9. Connect the flexible, codes-approved water supply line to the
water shutoff valve by threading the provided nut onto the
shutoff valve.
10. Place the end of the tubing into a bucket, and turn shutoff
valve ON.
11. Check for leaks around the saddle valve. Tighten any nuts or
connections (including connections at the valve) that leak.

Connect to Refrigerator

Parts Supplied
� 1/4" to 1/4" (6.35 mm to 6.35 mm) male-to-male coupling
NOTE: The flexible, codes-approved water supply line should
connect to the supply valve through the floor.
1. Unplug the refrigerator or disconnect power.
2. Connect the 7 ft (2.13 m) flexible codes-approved water tube
to the water supply valve.
a.
Compression sleeve
b.
Shutoff valve
c.
Packing nut
19