Publicité
BRACKET AND FEED THE WIRING OUT IN THE PROCESS. REPEAT THIS
PROCEDURE TO THE OTHER INDICATOR.
•
FIT ONE INDICATOR SPACER (ITEM 8) TO BOTH RUBBER INDICATOR
MOUNTS, BEFORE FITTING INTO THE LARGE SLOT ON EITHER SIDE OF THE
R&G LICENCE PLATE BRACKET AS SHOWN IN PICTURE 6). SECURE IN
PLACE BY REUSING THE PLASTIC MOUNTING PLATE IN THE SAME WAY
Page | 5
THAT IT WAS REMOVED.
IF FITTING R&G MINI INDICATORS:
•
FIT ONE LENGTH OF HEAT SHRINK TUBE TO THE WIRES OF EACH
INDICATOR.
•
POSITION TWO INDICATOR ADAPTORS (ITEM 4) AS SHOWN IN EXPLODED
DIAGRAM ABOVE. ENSURING THE SIDES FACING EACH OTHER HAVE THE
RAISED CENTRE PROFILE.
•
FIT EITHER INDICATOR THROUGH THE LARGE SLOT ON THE SIDE OF THE
TAIL TIDY, LOCATING THE INDICATOR ADAPTORS EITHER SIDE OF THE
METAL BRACKET, BEFORE FITTING THE NUT ONTO THE EXPOSED THREAD
AND TIGHTENING.
•
FROM THE KIT, TAKE R&G LICENCE PLATE BRACKET (ITEM 3) AND LOCATE
THE NEW LICENCE PLATE ILLUMINATOR (ITEM 5) TO THE THREE IN-LINE
HOLES ON THE BRACKET AS SHOWN IN PICTURE 7. SECURE USING THE M3
WASHERS AND NUTS PROVIDED IN THE KIT.
•
USE A SMALL AMOUNT OF SUPERGLUE OVER THE SURFACE OF THE NEW
LICENCE PLATE ILLUMINATOR (ITEM 5) AND LOCATE THE SHROUD (ITEM
6) OVER IT.
•
PROTECT THE LICENCE PLATE ILLUMINATOR WIRING USING ONE HEAT
SHRINK TUBE (ITEM 9) PROVIDED IN THE KIT.
•
FIT THE THREE CABLE CLIPS (ITEM 11) FROM THE KIT ON THE UNDERSIDE
OF THE R&G LICENCE PLATE BRACKET (ITEM 3) AS SHOWN IN PICTURE 8.
•
CLIP IN ALL THE WIRING TO EACH CABLE CLIP (ITEM 11) JUST FITTED
ACCORDINGLY AND FEED ALL THE WIRING THROUGH THE SLOT
PROVIDED IN THE BRACKET AS SHOWN IN PICTURE 9.
•
OFFER THE WHOLE TAIL TIDY ASSEMBLY TOWARDS THE SUBFRAME AS
ORIGINAL. SECURE USING M6 BOLTS, WASHERS AND NYLOC NUTS
PROVIDED IN THE KIT. SHOWN IN PICTURE 10 & 11. TIGHTEN ALL NYLOC
NUTS TO A SPECIFIED TORQUE SETTING.
•
CONNECT THE LICENCE PLATE ILLUMINATOR CONNECTORS TO THE MAIN
LOOM AS ORIGINAL IN THIS SCHEME:
PLEASE SWAP THE CONNECTORS OVER IF LIGHTS FAIL TO ILLUMINATE.
•
IF RE-FITTING THE OEM INDICATORS, RE-CONNECT THE CONNECTORS TO
THE MAIN LOOM AS ORIGINAL.
•
IF FITTING MINI INDICATORS, THE OEM INDICATOR CONNECTORS NEED TO
BE 'CUT & SHUT'. TO DO THIS, CUT THE CONNECTOR AT LEAST 50mm OF
WIRING OFF BOTH OEM INDICATORS. PEEL BOTH WIRE ENDS AND FIT
FEMALE BULLET CONNECTORS (ITEM 12) TO THE EXPOSED END OF BOTH
WIRES ON BOTH INDICATORS. CONNECT THESE FEMALE BULLET
CONNECTORS TO THE MALE BULLET CONNECTORS ON THE INDICATOR IN
THIS SCHEME:
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
1.
ILLUMINATOR RED ---------------- MAIN LOOM BROWN
2.
ILLUMINATOR BLACK ------------ MAIN LOOM BLACK
R&G Racing
www.rg-racing.com
Email:
LP0229
info@rg-racing.com
Publicité
