Standards Of Use - GGP ITALY SPA CR 430 Serie Manuel D'utilisation

EN

STANDARDS OF USE

NOTE - The number which precedes each paragraph links the
references in the text to the respective figures (listed on the pa-
ges 2 - 3).
1. FINISH ASSEMBLY
NOTE - The machine can be supplied with some of the
components already fitted.
WARNING - Unpacking and completing the assembly
should be done on a flat and stable surface, with enough
space for machine handling and its packaging, always
making use of suitable equipment.
Disposal of the packaging should be done in accordance
with the local regulations in force.
Complete machine assembly following the indications on the
instruction sheets enclosed with each part to be assembled.
2. DESCRIPTION OF CONTROLS
NOTE - The meanings of the symbols on controls are
explained on page 4 and following.
2.1
The engine is controlled by a dual action switch to pre-
vent starting it accidentally. To start, press the button (2) and
pull the lever (1). The engine automatically stops when the
lever (1) is released.
2.2
The cutting height is adjusted using the levers (1).
The four wheels must be at the same height.
MAKE THIS ADJUSTMENT ONLY WHEN THE BLADE IS
STOPPED.
2.3
In power-driven models, draw the lever (1) towards the
handle for forward movement.
The lawnmower stops moving forward when the lever is
released.
3. GRASS CUTTING
NOTE - This machine cuts lawns in various modes; before
starting work, prepare the machine based on how the lawn is
to be mowed.
MAKE THIS ADJUSTMENT WHEN THE ENGINE IS OFF.
3.1a
Preparation for grass cutting and collection in
grass-catcher:
– Lift the rear stone-guard (1) and correctly hook on the grass-
catcher (2) as shown in the figure.
3.1b
Preparation for grass cutting and rear discharge:
– Remove the grass-catcher and check that the rear stone-
guard (1) maintains its lowered position;
3.1c
Preparation for grass cutting and mulching (if pres-
ent):
– Lift the rear stone-guard (1) and fit the deflector cap (5) in the
outlet, keeping it slightly tilted to the right. Fasten it by fitting
the two pins (6) into the holes provided until the fastener
tooth clicks into place (7).
To remove the deflector cap (5), lift the stone-guard (1) and
press down on the centre until the tooth (7) is released.
3.2
Connect the extension cable correctly as indicated.
Start the engine by pressing the safety push-button (2) and
pulling the switchgear lever (1).
3.3
While cutting, ensure that the electric cable is always
behind you and on the area of grass already cut.
• In case of "mulching" or rear dumping of grass: always
avoid removing a large quantity of grass. Never cut more
than one third the total grass height in a single passage!
24
All manuals and user guides at all-guides.com
LAWN CARE RECOMENDATIONS
Each type of grass has different features and may thus require
different ways to care for the lawn; always read the instructions
on seed boxes for mowing height for the growth conditions in
the work area.
Keep in mind that most grass is made up of a stem and one or
more leaves. If leaves are fully cut, the lawn is damaged and
growth is more difficult.
The following indications generally apply:
– too low a cut causes grass tears and uprooting, with a "spot-
– in the summer, cutting must be higher to avoid the ground
– do not cut wet grass; this could reduce blade efficiency due
– for particularly high grass, initially mow at maximum admit-
The appearance of the lawn will improve if you alternate the
cutting in both directions at the same height.
FIRST disconnect the cable extension from the supply socket
(2) and THEN from the side of the lawnmower's switchgear (3).
WAIT FOR THE BLADE TO STOP before carrying out any type
of work on the machine.
IMPORTANT NOTE
Should the motor stop during use through overheating, wait
about 5 minutes before re-starting.
IMPORTANT - Regular, careful maintenance is essential for
keeping the safety level and original performance of the
machine unchanged in time.
Store the lawnmower in a dry place.
1) Wear strong working gloves during any cleaning, mainte-
2) Remove the grass debris after each cut and mud accumu-
3) Always ensure that ventilation openings are kept clear of
4) The paintwork on the inside of the chassis may peel off in
specialised Centre that has the most appropriate tools.
Only blades with the following codes must be used on this
machine:
Blades must always be marked «
product evolution, the above mentioned blade may be replaced
in time by others, with similar interchangeable and operating
safety characteristics.
Reassemble the blade (2) with the code and markings facing
the ground, following the order indicated in the illustration.
Tighten the central screw (1) using a torque wrench set to 16-
20 Nm.
the electrical components.
Do not use harsh products for cleaning the chassis.
Regulate the forward speed according to the lawn conditions
and the amount of grass removed.
ted" aspect;
from drying;
to sticky grass and tear the lawn;
ted machine height followed by a second mow after two or
three days.
3.4
When you have finishing mowing, release the lever (1).
4. ROUTINE MAINTENANCE
nance or adjustment operation on the machine.
lated inside the chassis to avoid their drying and thus mak-
ing the next start-up difficult.
debris.
time due to the abrasive action of the cut grass; in this case,
intervene promptly by touching up the paintwork using a
rustproof paint to prevent the formation of rust that would
lead to corrosion of the metal.
4.1
Each intervention on the blade is best if conducted at a
81004341/3 (for model 430)
81004346/3 (for model 480)
4.2
Do not use forced water and avoid wetting the motor or
» or «GGP». Given the