Memory Full - Kenwood KDC-BT742U Mode D'emploi

PROTECT (Blink):
The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Wire or insulate the speaker cable
properly and press the reset button. If
the "PROTECT" code does not disappear,
consult your nearest service center.
NA FILE: An Audio file is played with a format that this
unit can't support.
COPY PRO: A copy-protected file is played.
READ ERROR: The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
device again. If the error message is still
displayed, initialize the USB device or use
other USB devices.
NO DEVICE: The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
N/A DEVICE: • An unsupported USB device is connected.
• Connection to the iPod has failed.
➪ Check that the connected iPod is an iPod
that is supported. See <About Audio file>
(page 36) for information on supported
iPods.
NO MUSIC DATA/ERROR 15:
• The connected USB device contains no
playable audio file.
• Media was played that does not have data
recorded that the unit can play.
USB ERROR: Some trouble may have occurred to the
connected USB device.
➪ Remove the USB device, then cycle the
power switch to ON. If the same display is
repeated, use another USB device.
iPod ERROR: Connection to the iPod has failed.
➪ Remove the USB device and then
reconnect it.
➪ Confirm that the software for the iPod is
the latest version.
USB REMOVE (Blink):
The Remove mode has been selected for the
USB device/iPod. You can remove the USB
device/iPod safely.
NO NUMBER: • The calling party does not notify a caller ID.
• There is no phone number data.
NO DATA: • There is no outgoing call list.
• There is no incoming call list.
• There is no missed call list.
• There is no phone book list.
NO ENTRY: The cell-phone has not been registered
(pairing).
HF DISCONCT: The unit cannot communicate with the cell-
phone.
HF ERROR 07: The memory cannot be accessed.
➪ Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
HF ERROR 68: The unit cannot communicate with the cell-
phone.
➪ Turn off the power and on again. If this
message still appears, press the reset
button on the control unit.
UNKNOWN: The Bluetooth device cannot be detected.
DEVICE FULL: 5 Bluetooth device have already been
registered. No more Bluetooth device cannot
be registered.
PIN CODE NG: The PIN code is wrong.
CONNECT NG: The unit cannot be connected to the device.
PAIRING NG: Pairing error.
NO MATCHING: The voice tag is wrong. Voice cannot be
recognized because of an unregistered voice
tag, etc.
TOO SOFT: Voice is too small and cannot be recognized.
TOO LOUD: Voice is too large to be recognized.
TOO LONG: The word or utterance is too long to be
recognized.
NO PHONEBOOK:
Data is not contained in the phone book.
NO MESSAGE: No short message in In Box.
NO RECORD: The voice tag is not registered in the
phonebook.
MEMORY FULL: The number of voice tags reaches the
maximum number to be registered in the
phonebook.
FAV: NO MEMORY :
The procedure is not registered to Favorite
Preset Memory
NO ACCESS : The procedure preset with Favorite Control
cannot be available. The preset content may
not be recalled depending on the selected
source or mode.
NO VOICE : No call.
NO PANEL : The faceplate of the slave unit being
connected to this unit has been removed.
HD MEM FULL : The tag memory of HD Radio is FULL.
iPod MEM FULL :
The iPod memory is FULL.
NO TAG FNC : iPod which does not support the tag memory
is connected.
45
|
English