General Power Tool Safety Warnings - Makita HM1801 Manuel D'instructions

ENGLISH (Original instructions)
1. Switch lever
2. Indicator lamp
3. Bit with collar
4. Bit without collar
5. Bit
6. Tool retainer
7. Tool holder
8. When the bit is inserted
SPECIFICATIONS
Model
Blows per minute
Overall length
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for heavy chiselling and demolition
work as well as for driving and compacting with
appropriate accessories.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects to
the operation of other equipment. With a mains
impedance equal or less than 0.31 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
12. Do not point the tool at any one in the area when
operating. The bit could fly out and injure
4
All manuals and user guides at all-guides.com
Explanation of general view
9. When the bit is retained
10. Notched portion
11. Tool retainer shaft
12. Barrel
13. Commutator
14. Insulating tip
15. Carbon brush
16. Hex wrench 5
HM1801
1,100
824 mm
29.7 kg
HAMMER SAFETY WARNINGS
ENE046-1
1. Wear ear protectors. Exposure to noise can cause
ENF002-2 2. Use auxiliary handle(s), if supplied with the tool.
3. Hold power tool by insulated gripping surfaces,
ENF100-1
4. Wear a hard hat (safety helmet), safety glasses
5. Be sure the bit is secured in place before
6. Under normal operation, the tool is designed to
7. In cold weather or when the tool has not been
GEA010-1
8. Always be sure you have a firm footing. Be sure
9. Hold the tool firmly with both hands.
10. Keep hands away from moving parts.
11. Do not leave the tool running. Operate the tool
17. Motor housing cover
18. Cap rubber
19. Brush holder cap
20. Screwdriver
21. Cap
22. Lock nut wrench 20
23. Hex wrench 8
24. Hammer grease
HM1810
824 mm
32.3 kg
/II
hearing loss.
Loss of control can cause personal injury.
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
and/or face shield. Ordinary eye or sun glasses
are NOT safety glasses. It is also highly
recommended that you wear a dust mask and
thickly padded gloves.
operation.
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
used for a long time, let the tool warm up for a
while by operating it under no load. This will
loosen up the lubrication. Without proper warm-
up, hammering operation is difficult.
no one is below when using the tool in high
locations.
only when hand-held.
someone seriously.
1,100
GEB004-6