Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Preparing the Installation
Please observe the chapter „Safety instructions"!
It is important to pay attention to the correct mounting position of the LED outdoor
spotlight; install it only with the PIR sensor positioned on the bottom side. The arrow
marking on the mounting plate must point upwards in a vertical direction.
Install the LED outdoor spotlight only on a firm base, e.g., masonry. Use screws and,
if necessary, screw anchors that are suitable for the surface.
The LED outdoor spotlight must be installed so that it is out of the reach of children.
Select the mounting height depending on the on-site conditions.
Installation, Inserting the Batteries, Startup
• Undo first the single screw on the bottom using a suitable screwdriver (A).
• After that press and hold down the locking knob (B) while pulling the wall holder out by means
of the strap (C).
• Attach the wall holder with two suitable screws and, if necessary, wall plugs to the wall (the
distance between the holes is approx 39.5 mm). The textile strap should be placed behind
the wall mount here (do not cut!).
Pay attention to the correct mounting position of the wall holder! The arrow marks
inside and outside of the wall holder must face upwards.
Pay attention, when drilling and tightening the screws, that no cables or pipes are
damaged.
• Insert three type AA/Mignon batteries with the correct polarity into the battery compartment
inside the LED outdoor spotlight.
Take care that the small fabric strap is inside the battery compartment underneath
the batteries. In case of a battery change, the batteries are easily removed from the
battery compartment by using the fabric strap.
A battery chance is necessary when the brightness of the LED outdoor spotlight is conside-
rably reduced. Then change the batteries quickly, because the empty batteries can leak and
damage the product, resulting in loss of guarantee/warranty!
Please note:
You can use rechargeable batteries instead of conventional batteries to power the
LED outdoor spotlight. However, due to the lower capacity of the rechargeable bat-
teries and a lower voltage (rechargeable battery = 1.2 V, battery = 1.5 V), operating
time is much shorter. Rechargeable batteries are also more temperature sensitive
than batteries (e.g. in winter time!).
We therefore recommend using only high-quality batteries to power the LED outdoor
spotlight.
• Push in the locking knob of the wall holder (keep pressed) and put the LED outdoor spotlight
with the correct orientation on the wall holder (PIR sensor facing down) until the locking knob
clicks into place.
• Tighten the screw, which was previously removed, at the bottom, so that the LED outdoor
spotlight is fixated on the wall holder.
• To activate the LED outdoor spotlight, turn it on by the flip switch on the bottom (switch posi-
tion „ON"). The LED outdoor spotlight is now activated for a few seconds; then the light goes
out and the LED outdoor spotlight is ready for use.
The light is automatically switched on depending on the preset switching threshold
for ambient brightness. Please observe the information contained in the following
two chapters.
All manuals and user guides at all-guides.com
Settings and Operation
a) Setting the on-time (rotary control with time symbol)
With this knob you can set the on-time duration (a duration of 10 ± 5 seconds to 30 ± 10 se-
conds can be set). Turning it to the left in a counter-clockwise direction will reduce the power-on
time, while to the right in a clockwise direction will extend the duration.
b) Setting the switching threshold for the ambient brightness (rotary knob
With this knob you can set the switching threshold for ambient brightness that enables the PIR
sensor and turns on the LED outdoor spotlight in case of a heat change in the detection range.
Turning the rotary knob counter-clockwise to the left, in the direction of the moon symbol, me-
ans the PIR sensor is activated when it gets darker; turning it clockwise to the right, in direction
of the sun symbol, activates the motion detector in brighter conditions.
c) Alignment of the PIR Sensor
The horizontal detection angle of the PIR-Sensor is 130°, the vertical detection angle 60°.
By turning the PIR sensor to the left or to right, you can adjust the horizontal detection range
according to local circumstances.
d) Alignment of the two lamp heads
Both lamp heads can be swivelled individually to the left and right and also up and down; mo-
reover, the entire lamp head can be rotated. That way, you can adjust the area which should
be illuminated in the best way.
e) Switching the LED outdoor spotlight on/off
At the bottom of the LED outdoor spotlight is a flip switch. This has the following functions:
• Switch position „ON" (turned on)
• Switch position „OFF" (turned off)
Functional Test
For a functional test for the switching threshold of ambient brightness turn the rotary knob all
the way into the direction of sun icon. The knob for the power-on time should be in the base
position (turn in a counter-clockwise direction all the way to the left until it stops).
Now cross the detection range. The two lamps of the LED outdoor spotlight will turn on when
the PIR sensor detects a heat change in the detection area.
When you stand still (and the PIR sensor can no longer detect any heat changes), both lamps
should go out after a few seconds.
Care and Cleaning
• Never use abrasive cleaning agents, cleaning alcohol or other chemical solutions, since the-
• Use a dry, lint-free cloth to clean the product.
When you turn the PIR sensor to the left while facing the PIR sensor, you will see
two rotary knobs. They are used to set the on-time and the brightness threshold to
activate the light.
If the PIR sensor detects a heat change again in the detection range within the on-
time cycle, the power-on time will restart anew.
Only if no more heat changes are detected in the detection range during on-time will
the LED outdoor spotlight go out.
with sun/moon icon)
An arrow mark on the front of the PIR sensor shows you the centre of the horizontal
detection angle.
If the arrow on the front of the PIR sensor points to the arrow on the LED outdoor
spotlight, the detection range is centred.
The LED outdoor spotlight is switched on. The PIR sensor is enabled when ambient bright-
ness falls below the threshold set with the related knob. If, in this case, the PIR sensor detects
a heat change in the detection area (for example, when a person enters the detection area),
the two lamps of the LED outdoor spotlight will be enabled for the time set with the knob.
If the PIR sensor detects a heat change again in the detection range within the on-
time cycle, the power-on time will restart anew.
Only if no more heat changes are detected in the detection range during on-time will
the LED outdoor spotlight go out.
The LED outdoor spotlight is disabled.
You can use this switch position if you do not need the LED outdoor spotlight for a
longer time.
se could damage the enclosure or even impair operation.
Publicité
Table des Matières
