Use And Care; Operation - Broan Elite RM60000 Serie Instructions

15. USE AND CARE

Grease Filters
The grease filters should be cleaned frequently. Use a
warm detergent solution. Grease filters are dishwasher
safe. Wash more often if your cooking style generates
greater grease—like frying foods or wok cooking.
Remove filters by pushing filters towards the back of hood
and rotating filters downward.
Blower Cleaning
Remove the filters in order to access the blower. Vacuum
blower to clean. Do not immerse in water. Refer to blower
instruction manual for more details.
Grease Rail
The grease rail should be cleaned frequently, especially if
baffle filters are used.
Remove filters, then, disassemble the grease rail from the hood
by removing its 3 retaining screws. See illustration below.
HD0069
Refer to Stainless steel cleaning in Hood Cleaning section
below. Once the grease rail is clean and dry, reassemble it
to the hood and reinstall filters.
Hood Cleaning
Stainless steel cleaning: How to maintain its "BRIGHT LOOK"
Do:
• Regularly wash with clean cloth or rag soaked with
warm water and mild soap or liquid dish detergent.
• Always clean in the direction of original polish lines.
• Always rinse well with clear water (2 or 3 times) after
cleaning. Wipe dry completely.
• You may also use a specialized household stainless
steel cleaner.
Don't:
• Do not use any steel or stainless steel wool or any
other scrapers to remove stubborn dirt.
• Do not use any harsh or abrasive cleansers.
• Do not allow dirt to accumulate.
• Do not let plaster dust or any other construction
residues reach the hood. During construction/renovation,
cover the hood to make sure no dust sticks to stainless
steel surface.
Avoid: When choosing a detergent
• Any cleaners that contain bleach will attack stainless steel.
• Any products containing: chloride, fluoride, iodide,
bromide will deteriorate surfaces rapidly.
• Any combustible products used for cleaning such as
acetone, alcohol, ether, benzol, etc., are highly explosive
and should never be used close to a range.
Enamel finish:
Clean with warm water and mild detergent only.
When discoloration occcurs, use a good enamel polish
such as automotive polish. (DO NOT use rough abrasive
cleaner or porcelain cleaner.)
All manuals and user guides at all-guides.com
- 11 -

16. OPERATION

Always turn ON your hood before you begin cooking in
order to establish an air flow in the kitchen. Let the blower run
for a few minutes to clear the air after you turn off the range.
This will help keep the whole kitchen cleaner and brighter.
4
3
1
HC0004
1. Warming lamps
2. Warming lamp switches
3. Halogen lights
Warming lamps (Infrared)
Each warming lamp (item 1 in picture above) is controlled
with is own ON/OFF switch (item 2 on picture above).
Use only BR40 Size, 250 W max., Infrared bulbs (purchase
separately).
WARNING
!
Never place highly flammable material under
warming lamps.
Cooktop Lighting (Halogen)
A double set of ON/OFF switches (item 4 on picture above)
control the halogen lights (item 3 on picture above).
The front rocker controls the center light. The rear rocker
controls both side lights. Select one, two, or three lights for
best cooktop lighting.
Use PAR 20, 50 W halogen bulbs (purchase separately).
Blower
The blower is operated using two (2) controls.
Use the red, lighted ON/OFF switch (item 5 on picture
above) to start and stop the blower. When turned on, the
blower will operate at the previous setting of the speed
control (item 6 on picture above).
Turn the speed control knob clockwise to decrease blower
speed—counterclockwise to increase speed.
HEAT SENTRY
This hood is equipped with a HEAT SENTRY thermostat.
This thermostat is a device that will turn on or speed up the
blower if it senses excessive heat above the cooking surface.
1) If blower is OFF—it turns blower ON to HIGH speed.
2) If blower is ON at a lower speed setting—it turns the
blower up to HIGH speed.
When the temperature level drops to normal, the blower
will return to its original setting.
WARNING
!
The HEAT SENTRY can start the blower even if
the hood is turned OFF. In this case, it is impossible
to turn the blower OFF with blower switch. If you
must stop the blower, do it from the main
electrical panel.
6
5
3 3
1
2
4. Halogen light switches
5. ON/OFF Blower switch
6. Blower speed control