Correcting Horizontal Mitre Angles; Correcting Vertical Mitre Angles; Replacing The Tabletop Insert - Festool KAPEX KS 120 EB Notice D'utilisation D'origine

9.2

Correcting horizontal mitre angles

If the pointer (13.2) no longer rests on the
preset mitre angle values, you can loosen
the screw (13.1) and readjust the pointer.
If the actual (sawn) mitre cut deviates from
the preset value, you can correct this value
accordingly:
– Engage the saw unit in the 0° position.
– Loosen the three screws (13.3) that secure
the scale to the saw table.
– Slide the scale together with the saw unit
until the actual value is 0°. You can check
this by setting an angle between the stop
ruler and the saw blade.
– Tighten the three screws (13.3) again.
– Check the angle setting by making a test
cut.
9.3

Correcting vertical mitre angles

If the actual value no longer corresponds
with the preset value, you can correct this
value accordingly:
– Engage the saw unit in the 0° position.
– Open both screws (23.1).
– Swivel the saw unit until the actual value
is 0°. You can check this by setting an
angle between the saw table and the saw
blade.
– Tighten the two screws (23.1) again.
– Check the angle setting by making a test cut.
If the pointer (22.2) no longer rests on
the preset value, you can loosen the screw
(22.1) and readjust this value.
9.4

Replacing the tabletop insert

Never work with a worn table insert (20.1),
replace it with a new one.
– To replace the table insert, unscrew the six
screws (20.2).
9.5 Cleaning or replacing window for
laser (KS 120 EB only)
The window (21.2) for protecting the laser
can become dirty during operation. It can be
removed for cleaning or replacement.
– Release the screw (21.5) by approx. 2 ro-
tations.
– Press the window at the same time in the
directions (21.3) and (21.4).
– Remove the window.
– Clean the window or replace it with a new one.
– Fit the cleaned/new window. Both of the
pegs (21.1) on the window must snap into
the recesses of the upper hood as shown
in Fig. 21.
All manuals and user guides at all-guides.com
23
– Tighten the screw (21.5).
10 Accessories
Use only original Festool accessories and
Festool consumable material intended for
this machine because these components are
designed specifi cally for the machine. Using
accessories and consumable material from
other suppliers will most likely affect the
quality of your working results and limit any
warranty claims. Machine wear or your own
personal workload may increase depending
on the application. Protect yourself and your
machine, and preserve your warranty claims
by always using original Festool accessories
and Festool consumable material!
Festool offers you a comprehensive range of
accessories for your circular cross-cut saw:
• Saw blades for different materials.
• Trimming attachment (workpiece support
surface with integral measurement scale):
allows you to support and machine long
workpieces accurately.
• Cornice stop: support for sloping strip ma-
terial and cornices.
Other accessories and order numbers for
accessories and tools can be found in the
Festool catalogue or on the Internet under
www.festool.com.
11 Disposal
Do not throw the power tool in your house-
hold waste! Dispose of the machine, acces-
sories and packaging at an environmentally-
responsible recycling centre! Observe the
valid national regulations.
EU only: European Directive 2002/96/EC
stipulate that used electric power tools must
be collected separately and disposed of at an
environmentally responsible recycling centre.
12 Warranty
For our tools, we give warranty for material
and production defects in accordance with
the locally applicable legal provisions, but in
any case for at least 12 months. Within the
EU member states, the warranty period is
24 months (verifi cation through invoice or
delivery note). Damage caused by, in par-
ticular, natural wear, overloading, incorrect
handling, or damage caused by the operator,
or damage caused through use of the equip-
ment contrary that specifi ed in the Operating
Instructions, or damage which was known
at the time of purchase, is not covered by