Table des Matières
Publicité
FM/AM
Compact Disc Player
Installation/Connections
Installation/Connexions
CDX-GT650UI
©2010 Sony Corporation Printed in Thailand
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Front speaker
Haut-parleur avant
Rear speaker
Haut-parleur arrière
All manuals and user guides at all-guides.com
4-193-832-11(1)
× 2
× 4
Active subwoofer
Caisson de graves actif
Power amplifier
Amplificateur de puissance
A
SUB OUT ( MONO )
B
BUS AUDIO IN
Satellite radio tuner
(XM/SIRIUS)*
Syntoniseur radio satellite
(XM/SIRIUS)*
BUS CONTROL IN
Cautions
This unit is designed for negative ground (earth) 12 V
DC operation only.
Do not get the leads under a screw, or caught in moving
parts (e.g. seat railing).
Before making connections, turn the car ignition off to
avoid short circuits.
Connect the yellow and red power supply leads only
after all other leads have been connected.
Run all ground (earth) leads to a common ground
(earth) point.
Be sure to insulate any loose unconnected leads with
electrical tape for safety.
The use of optical instruments with this product will
increase eye hazard.
Notes on the power supply lead (yellow)
When connecting this unit in combination with other
stereo components, the connected car circuit's rating
must be higher than the sum of each component's fuse.
When no car circuits are rated high enough, connect
the unit directly to the battery.
Parts Iist
The numbers in the list are keyed to those in the
instructions.
The bracket
and the protection collar
are
attached to the unit before shipping. Before mounting
the unit, use the release keys
to remove the bracket
from the unit. For details, see "Removing the
protection collar and the bracket (
)" on the reverse
side of the sheet.
Keep the release keys
for future use as they are
also necessary if you remove the unit from your
car.
Caution
Handle the bracket
carefully to avoid injuring your
fingers.
Catch
Note
Before installing, make sure that the catches on both sides of the bracket
are bent inwards 2 mm (
3
/
in). If the catches are straight or bent
32
outwards, the unit will not be installed securely and may spring out.
FRONT
AUDIO OUT
REAR
AUDIO OUT
* not supplied
non fourni
Connection example
Notes (
-A)
Be sure to connect the ground (earth) lead before connecting the
amplifier.
The alarm will only sound if the built-in amplifier is used.
Note on satellite radio tuner (
-B)
This unit does not support the XM radio tuner
XMDSON100.
Connection diagram
To a metal surface of the car
First connect the black ground (earth) lead, then connect the yellow
and red power supply leads.
To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see "Notes on the control and power supply leads."
To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting any other system
may damage the unit.
To the interface cable of a car telephone
To a car's illumination signal
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
To the +12 V power terminal which is energized
in the accessory position of the ignition switch
Notes
If there is no accessory position, connect to the +12 V power
(battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
When your car has a built-in FM/AM antenna (aerial) in the rear/
side glass, see "Notes on the control and power supply leads."
To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground (earth) lead to a metal surface
of the car first.
Publicité
Table des Matières
