Warranty; Swimming Pool Energy Saving Tips; Codes And Standards; Technical Assistance - Jandy JRT Serie Manuel D'installation

Jandy ® JRT Series Heat Pumps
WARNING
Hyperthermia occurs when the internal body
temperature reaches a level several degrees above
the normal body temperature of 98.6°F (37°C).
Symptoms include dizziness, fainting, drowsiness,
lethargy, and an increase in the internal body
temperature. The effects of hyperthermia include:
• Lack of awareness of impending hazard
• Failure to perceive heat
• Failure to recognize need to leave spa
• Physical inability to leave spa
• Fetal damage in pregnant women
• Unconsciousness resulting in a danger of
drowning
WARNING
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
WARNING
PREVENT CHILD DROWNING: Do not let
anyone, especially small children, sit, step, lean or
climb on any equipment installed as part of your
pool's operational system. Locate the components
of your operational system at least 1.5m (5 ft.) from
the pool so children cannot use the equipment while
in the pool and be injured or drown.

Swimming Pool Energy Saving Tips

It is important to note that a heat pump will not heat
a pool as fast as a large gas or electric pool heater. If
the pool water is allowed to cool significantly, it may
take several days to return to the desired swimming
temperature. For weekend use, it is more economical
to maintain the pool water temperature at or near your
desired swimming temperature. If you do not plan to
use your pool for a prolonged period, then you might
choose to turn the heat pump completely off or decrease
the temperature setting of the control several degrees to
minimize energy consumption.
Jandy offers the following recommendations to help
conserve energy and minimize the cost of operating
your heat pump without sacrificing comfort.
1. The American Red Cross recommends a maximum
water temperature of 78°F (25°C). Use an accurate
pool thermometer. A difference of 4°F (2°C),
between 78°F and 82°F (26°C and 28°C), will
significantly increase energy consumption.
2. Carefully monitor the water temperature of your
pool in the summertime. You can reduce heat
pump usage due to warmer air temperatures.
3. During the winter or when on vacation for longer
than a week, turn off the heat pump.
|
Installation and Operation Manual
ENGLISH
4. Find the proper setting on the heat pump
temperature control and use the Set Point Lockout
or lock the cover on the heat pump controller to
discourage further adjustments.
5. Set the pump time clock to start the pump no
earlier than 6:00 AM during the pool heating
season. This is the time when nightly heat loss
balances.
6. Where possible, shelter the pool from prevailing
winds with well-trimmed hedges or other
landscaping, cabanas, or fencing.
7. The use of an automatic pool cover, if installed,
provides a valuable safety feature, reduces heat
loss, conserves chemicals, and reduces the load on
filtration systems..
8. The use of a solar blanket can reduce the heat loss
caused by evaporation on the surface area of the
pool.
1.3

Warranty

The Jandy JRT heat pump is sold with a limited factory
warranty.
Make all warranty claims to your Jandy
directly to Jandy. Claims must include the heat pump
serial number and model (this information can be found
on the rating plate), installation date, and name of the
installer. Shipping costs are not included in the warranty
coverage.
The warranty does not cover damage caused by
improper assembly, installation, operation, winterizing,
field modification, or failure to earth bond and
properly ground the unit. Any changes to the heat
pump, evaporator, heat exchanger, wiring, or improper
installation may void the warranty.
1.4

Codes and Standards

The Jandy JRT heat pump is listed by ETL
complying with the latest edition of the "UL Standard
for Electrical Heat Pumps, Air-Conditioners, and
Dehumidifiers", UL 60335-2-40 and CSA No. 60335-2-
40.
All Jandy heat pumps must be installed in accordance
with the local building and installation codes as per the
utility or authority having jurisdiction. All local codes
take precedence over national codes. In the absence of
local codes, refer to the latest edition of the National
Electrical Code (NEC ) in the United States and
® ®
the Canadian Electrical Code (CEC
installation.
1.5

Technical Assistance

Consult the Jandy technical support department or
your local Jandy dealer with any questions or problems
involving your Jandy equipment. An experienced
technical support staff is ready to assist you in assuring
the proper performance and application of Jandy
products. For technical support call the Jandy technical
support department at (800) 822-7933.
Page 3
dealer or
®
as
®
) in Canada for
®