Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Page 4
ENGLISH
WARNING
Prolonged immersion in hot water can induce
hyperthermia.
WARNING
Hyperthermia occurs when the internal body
temperature reaches a level several degrees above
the normal body temperature of 98.6°F (37°C).
Symptoms include dizziness, fainting, drowsiness,
lethargy, and an increase in the internal body
temperature. The effects of hyperthermia include:
•
Lack of awareness of impending hazard
•
Failure to perceive heat
•
Failure to recognize need to leave spa
•
Physical inability to leave spa
•
Fetal damage in pregnant women
•
Unconsciousness resulting in a danger of
drowning
Swimming Pool Energy Saving Tips
It is important to note that a heat pump will not heat
a pool as fast as a large gas or electric pool heater. If
the pool water is allowed to cool significantly, it may
take several days to return to the desired swimming
temperature. For weekend use, it is more economical
to maintain the pool water temperature at or near your
desired swimming temperature. If you do not plan to
use your pool for a prolonged period, then you might
choose to turn the heat pump completely off or decrease
the temperature setting of the control several degrees to
minimize energy consumption.
Zodiac offers the following recommendations to help
conserve energy and minimize the cost of operating
your heat pump without sacrificing comfort.
1.
The American Red Cross recommends a maximum
water temperature of 78°F (25°C). Use an accurate
pool thermometer. A difference of 4°F (2°C),
between 78°F and 82°F (26°C and 28°C), will
significantly increase energy consumption.
2.
Carefully monitor the water temperature of your
pool in the summertime. You can reduce heat
pump usage due to warmer air temperatures.
3.
During the winter or when on vacation for longer
than a week, turn off the heat pump.
4.
Find the proper setting on the heat pump
temperature control and use the Set Point Lockout
or lock the cover on the heat pump controller to
discourage further adjustments.
5.
Set the pump time clock to start the pump no
earlier than 6:00 AM during the pool heating
season. This is the time when nightly heat loss
balances.
6.
Where possible, shelter the pool from prevailing
winds with well-trimmed hedges or other
landscaping, cabanas, or fencing.
|
Jandy
®
JE Heat Pumps
Installation and Operation Manual
7.
The use of an automatic pool cover, if installed,
provides a valuable safety feature, reduces heat
loss, conserves chemicals, and reduces the load on
filtration systems..
8.
The use of a solar blanket can reduce the heat loss
caused by evaporation on the surface area of the
pool.
1.3
The Jandy JE heat pump is sold with a limited factory
warranty.
Make all warranty claims to your Zodiac
directly to Zodiac. Claims must include the heat pump
serial number and model (this information can be found
on the rating plate), installation date, and name of the
installer. Shipping costs are not included in the warranty
coverage.
The warranty does not cover damage caused by
improper assembly, installation, operation, winterizing,
field modification, or failure to earth bond and
properly ground the unit. Any changes to the heat
pump, evaporator, heat exchanger, wiring, or improper
installation may void the warranty.
1.4
The Jandy JE heat pump is listed by ETL
with the latest edition of the "UL Standard for Safety for
Heating and Cooling Equipment", UL 1995 and CSA
C22.2 No. 236.
All Zodiac heat pumps must be installed in accordance
with the local building and installation codes as per the
utility or authority having jurisdiction. All local codes
take precedence over national codes. In the absence of
local codes, refer to the latest edition of the National
Electrical Code
the Canadian Electrical Code (CEC
installation.
1.5
Consult the Zodiac technical support department or
your local Zodiac dealer with any questions or problems
involving your Zodiac equipment. An experienced
technical support staff is ready to assist you in assuring
the proper performance and application of Zodiac
products. For technical support call the Zodiac technical
support department at (800) 822-7933.
1.6
The following items are needed and are to be supplied
by the installer for all heat pump installations:
1.
Plumbing connections (2").
2.
Level surface for proper drainage. (See equipment
pad for pitch requirements)
Warranty
Codes and Standards
(NEC
) in the United States and
®
®
Technical Assistance
Materials Needed For Installation
dealer or
®
as complying
®
) in Canada for
®
Publicité
Chapitres
Table des Matières
Dépannage
