Section 1. General Information; Spa/Hot Tub Safety Rules; Introduction; Consumer Information And Safety - Jandy JRT Serie Manuel D'installation

Page 2
ENGLISH

Section 1. General Information

1.1

Introduction

This manual provides installation and operation
instructions for the Jandy JRT models of heat pumps.
Read these installation and operation instructions
completely before proceeding with the installation.
Consult Zodiac Pool Systems LLC ("Zodiac") with any
questions regarding this equipment. To obtain additional
copies of this manual contact us at 800-822-7933.
Zodiac Pool Systems LLC
2882 Whiptail Loop #100
Carlsbad, CA 92010 USA
The Jandy JRT heat pump gets electrical power from an
external source and provides a dual digital thermostat
control system for pool/spa combinations or preheat
convenience.
This heat pump is specifically designed for heating
fresh water swimming pools and spas. Do not use it
as a general service heater. Consult your dealer for the
appropriate Jandy products for these applications.
®
NOTE "Fresh water swimming pools and spas" include
systems that utilize saltwater chlorine generator
units, such as the Jandy AquaPure
Chlorine Generator. Please ensure that the salt
content of the pool/spa does not exceed
4500 ppm and water flow rate is within
30-70 gpm (114-265 lpm). Always install any
type of sanitation device on the outlet of the
heater with a check valve between the heater
outlet and sanitation device. See Section 3.3
ATTENTION
Installation and service must be performed by a
qualified installer or service agency.
To the Installer:
To the User:
1.2

Consumer Information and Safety

The Jandy JRT series of heat pumps are designed
and manufactured to provide many years of safe
and reliable service when installed, operated and
maintained according to the information in this manual
and the installation codes referred to in later sections.
Throughout the manual, safety warnings and cautions
are identified by the " " symbol. Be sure to read and
comply with all of the warnings and cautions.
Jandy ® JRT Series Heat Pumps
Electronic
®
After installation, these
instructions must be
given to the homeowner
or left on or near the
heat pump.
This manual contains
important information
that will help you
in operating and
maintaining this heat
pump. Please retain it
for future reference.
|
Installation and Operation Manual

Spa/Hot Tub Safety Rules

WARNING
The U.S. Consumer Product Safety
Commission warns that elevated water
temperature can be hazardous. Consult heater
operation and installation instructions for
water temperature guidelines before setting
temperature.
WARNING
The following "Safety Rules for Hot Tubs,"
recommended by the U.S. Consumer Product
Safety Commission, should be observed when
using the spa.
WARNING
Spa or hot tub water temperature should never
exceed 104°F (40°C). One hundred degrees
Fahrenheit (100°F [38°C]) is considered
safe for a healthy adult. Special caution is
recommended for young children.
WARNING
The drinking of alcoholic beverages
before or during spa or hot tub use can
cause drowsiness which could lead to
unconsciousness, and subsequently result in
drowning.
WARNING
Pregnant women take note! Soaking in water
above 102°F (38.5°C) can cause fetal damage
during the first three (3) months of pregnancy
(which could result in the birth of a brain-damaged
or deformed child). If pregnant women are going
to use a spa or hot tub, they should make sure
the water temperature is below 100°F (38°C)
maximum.
WARNING
The water temperature should always be checked
with an accurate thermometer before entering a spa
or hot tub. Temperature controls may vary by as
much as 1F° (1°C).
WARNING
Persons with a medical history of heart disease,
diabetes, circulatory or blood pressure problems
should consult their physician before using a hot tub
or spa.
WARNING
Persons taking any medication which induces
drowsiness (e.g., tranquilizers, antihistamines, or
anticoagulants) should not use spas or hot tubs.
WARNING
Prolonged immersion in hot water can induce
hyperthermia.