Scheppach BCCD70-20ProS Traduction Des Instructions D'origine page 21

Noise and vibration
m Warning: Noise at the workplace can exceed 85
dB (A). In this case, noise protection measures are
necessary for the user (wear hearing protection!).
Noise output in dB
Sound power level L
WA
Sound pressure level L
pA
Uncertainty K
wa/pA
Vibration value
Vibration a
h
Uncertainty K
h
9. Unpacking
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage. Inform the transport agent immediately of
any faults. Later complaints cannot be considered.
• If possible, store the packaging until the warranty
period has expired.
• Familiarize yourself with the machine with the help
of the operating instructions manual before using it.
• Use only original parts for accessories as well as
consumables and spare parts. Spare parts can be
obtained from your scheppach retailer.
• Please quote our article numbers as well as type
and production year in all your orders.
m ATTENTION!
The device and packaging materials are not toys!
Children must not be allowed to play with plas-
tic bags, film and small parts! There is a risk of
swallowing and suffocation!
10. Construction
Warning!
Always remove the battery pack before making ad-
justments to the equipment.
Additional handle (11) (Fig. A, B)
Only use the hammer drill with the additional
handle for safety reasons.
The additional handle (11) allows the user to maintain
added grip during use.
The machine must not be used without the additional
handle (11) for safety reasons.
The additional handle (11) is fastened to the hammer
drill through clamping.
• Turning the handle anticlockwise (looking from the
handle) will release the clamp.
• Turning the handle clockwise will tighten the clamp.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
85 dB(A) (EN ISO 3744)
74 dB(A) (EN ISO 11201)
5 dB(A)
7,1 m/s²
1,5 m/s²
• First release the additional handle clamp (11).
• You can subsequently fasten the additional handle
(11) in the working position that is most comfortable
for you (Fig. A and B).
• Now turn the additional handle (11) in the opposite
direction again until the additional handle (11) is se-
cure.
11. Installation
m Important!
You must fully assemble the appliance before using it
for the first time!
To ensure that the Li battery pack provides long ser-
vice you should take care to recharge it promptly. You
must recharge the battery pack when you notice that
the power of the cordless equipment drops.
Insertion / removal of a batterypack into the ap-
pliance
Ensure that the appliance is switched off before insert-
ing the battery. The insertion of a battery into an electri-
cal appliance that is switched on can lead to accidents.
Inserting the rechargeable battery pack:
Move the rotation switch (2) into the middle position
(lock) and push the rechargeable battery pack (5) into
the handle until it engages.
Removing the rechargeable battery pack:
Press the release button (6) and remove the re-
chargeable battery pack.
Used batteries
If a fully recharged battery lasts for considerably
shorter operating times, the battery is used up and
needs to be replaced. Only use an OEM battery pack
replacement available from our Customer Service.
Changing tools
• Your cordless electric drill / screwdriver has a fully
automatic spindle lock and is fitted with an enclosed
keyless chuck incorporating the latest technology.
Once the motor has come to a halt, the drive shaft
is automatically locked, so that the chuck (9) can be
opened simply by turning it . After you have insert-
ed the required bit and fixed it in place by turning
the chuck , you can immediately continue working.
The spindle lock releases itself automatically when
the motor is started (by operation of the ON / OFF
switch (3) ).
Torque pre-selection
• You can adjust the torque by using (8) torque prese-
lection.
• Select a low setting for small screws, soft workma-
terial.
GB | 21