Mitsubishi Electric CITY MULTI PLFY-P32VBM-E Manuel D'utilisation page 9

6. Timer
6.1. For Wired Remote-controller
You can use Function Selection of remote controller to select which of
three types of timer to use: Weekly timer,
Off timer.
6.1.1. Weekly Timer
The weekly timer can be used to set up to eight operations for each
day of the week.
• Each operation may consist of any of the following: ON/OFF time
together with a temperature setting, or ON/OFF time only, or tem-
perature setting only.
• When the current time reaches a time set at this timer, the air condi-
tioner carries out the action set by the timer.
Time setting resolution for this timer is one minute.
Note:
*1. Weekly Timer/Simple Timer/Auto Off Timer cannot be used at the same
time.
*2. The weekly timer will not operate when any of the following conditions is
in effect.
The timer feature is off; the system is in an malfunction state; a test run
is in progress; the remote controller is undergoing self-check or remote
controller check; the user is in the process of setting a function; the user
is in the process of setting the timer; the user is in the process of setting
the current day of the week or time; the system is under central control.
(Specifically, the system will not carry out operations (unit on, unit off, or
temperature setting) that are prohibited during these conditions.)
Operation No.
Day Setting
SUN
TEMP.
MENU ON/OFF
BACK MONITOR/SET DAY
PAR-21MAA CLOCK
Simple timer, or
ON
°C
WEEKLY
ON/OFF
FILTER
CHECK TEST
OPERATION
CLEAR
<How to Set the Weekly Timer>
1. Be sure that you are at a standard control screen, and that the weekly
timer indicator is shown in the display.
Auto
2. Press the Timer Menu button
screen (at ). (Note that each press of the button toggles the display
between "Set Up" and "Monitor".)
3. Press the Timer On/Off (Set Day) button
advances the display at
quence: "Sun Mon Tues Wed Thurs Fri Sat"
"Sat"
"Sun Mon Tues Wed Thurs Fri Sat"...
4. Press the or Operation button (
the appropriate operation number (1 to 8)
* Your inputs at Steps 3 and 4 will select one of the cells from the
matrix illustrated below.
(The remote-controller display at left shows how the display would
appear when setting Operation 1 for Sunday to the values indi-
cated below.)
Setup Matrix
Op No. Sunday
No. 1
• 8:30
• ON
• 23 °C
No. 2 • 10:00
• OFF
...
No. 8
<Operation 1 settings for Sunday>
Start the air conditioner at 8:30, with
the temperature set to 23 °C.
Note:
By setting the day to "Sun Mon Tues Wed Thurs Fri Sat", you can set the
same operation to be carried out at the same time every day.
(Example: Operation 2 above, which is the same for all days of the week
<Setting the Weekly Timer>
Shows the time setting
SUN
°C
5. Press the appropriate Set Time button
sired time (at ).
* As you hold the button down, the time first increments in one-minute
intervals, then in ten-minute intervals, and then in one-hour intervals.
6. Press the ON/OFF button
OFF), at .
* Each press changes the next setting, in the following sequence: No
display (no setting)
, so that the "Set Up" appears on the
to set the day. Each press
to the next setting, in the following se-
"Sun"
or ) as necessary to select
.
Monday ...
• 10:00 • 10:00
• OFF • OFF
<Operation 2 settings for every day>
Turn off the air conditioner at 10:00.
Shows the temperature setting
* Does not appear if temperature is not set.
ON
WEEKLY
Shows the selected operation (ON or OFF)
*Does not appear if operation is not set.
as necessary to set the de-
to select the desired operation (ON or
"ON" "OFF"
... "Fri"
Saturday
• 10:00
• OFF
9