FALMEC Professional Marte Pro Mode D'emploi page 13

CLEANING OF EXTERNAL SURFACES
You are advised to clean the external surfaces of the hood at least once every
15 days to prevent oily substances and grease from sticking to them.
Alternatively and for all the other types of surfaces, it can be cleaned using a
damp cloth, slightly moistened with mild, liquid detergent or denatured alcohol.
Finish off cleaning by rinsing well and drying with soft cloths.
Do not use too much water next to the push button control pan-
el and lighting devices in order to prevent humidity from reach-
ing electronic parts.
The glass panels can only be cleaned with specifi c, non-corrosive or non-abra-
sive detergents using a soft cloth.
The Manufacturer declines all responsibility for failure to comply with these in-
structions.
CLEANING OF INTERNAL SURFACES
It is forbidden to clean electrical parts, or parts related to the mo-
tor inside the hood, with liquids or solvents.
For the internal metal parts, see the previous paragraph.
METAL ANTI-GREASE FILTERS
It is advised to frequently wash the metal fi lters (at least once a month) leaving
them to soak in boiling water and washing up liquid for 1 hour, taking care not
to bend them.
Do not use corrosive, acid or alkaline detergents.
Rinse them well and wait for them to be completely dry before reassembling
them.
They are dishwasher safe.
To extract and insert the metal anti-grease fi lters see the picture.
1
LIGHTING
The range hood is equipped with high effi ciency, low consumption LED spot-
lights with extremely long duration under normal use conditions.
Should the LED spotlight need to be replaced, proceed as shown in the fi gure.
1
2
2
3
12V
GREASE DRIP TRAY
It is advisable to clean the tray every 15 days.
Do not use corrosive, acid or alkaline detergents.
For more thorough cleaning, remove the oil collection tray (see fi gure) and wash
it with hot water and washing up liquid. Rinse it well and wait for it to be com-
pletely dry before reassembling it. They are dishwasher safe.
1
DISPOSAL AFTER END OF USEFUL LIFE
The crossed-out trash or refuse bin symbol on the appliance means
that the product is WEEE, i.e. "Waste electrical and electronic equip-
ment'' , accordingly it must not be disposed of with regular unsort-
ed waste (i.e. with ''mixed household waste''), but it must be disposed
of separately so that it can undergo specifi c processing for its re-use, or
a specifi c treatment, to remove and safely dispose of any substances that may be
harmful to the environment and remove the raw materials that can be recycled.
Proper disposal of these products contributes to saving valuable resources and
avoid potential negative eff ects on personal health and the environment, which
may be caused by inappropriate disposal of waste.
You are kindly asked to contact your local authorities for further information
regarding the designated waste collection points nearest to you. Penalties for
improper disposal of such waste can be applied in compliance with national
regulations.
INFORMATION ON DISPOSAL IN EUROPEAN UNION COUNTRIES
The EU WEEE Directive was implemented diff erently in each country, accord-
ingly, if you wish to dispose of this appliance we suggest contacting your local
authorities or dealer to fi nd out what the correct method of disposal is.
INFORMATION ON DISPOSAL IN NON-EUROPEAN UNION COUNTRIES
The crossed-out trash or refuse bin symbol is only valid in the European Union: if
you wish to dispose of this appliance in other countries, we suggest contacting
your local authorities or dealer to fi nd out what the correct method of disposal is.
WARNING!
The Manufacturer reserves the right to make changes to the equipment at any
time and without prior notice. Printing, translation and reproduction, even par-
tial, of this manual are bound by the Manufacturer's authorisation.
Technical information, graphic representations and specifi cations in this manual
are for information purposes and cannot be divulged.
This manual is written in Italian. The Manufacturer is not responsible for any tran-
scription or translation errors.
13
2
3