Hilti PR 2-HS Mode D'emploi page 26

Short-circuiting the battery terminals presents a risk
of fire, explosion or contact with caustic substances.
i) Do not charge or continue to use damaged bat-
teries (e.g. batteries with cracks, broken parts,
bent or pushed-in and/or pulled-out contacts).
j) Use only the PUA 81 AC adapter, PUA 82 motor
vehicle power adapter or other chargers recom-
mended by the manufacturer to power the tool or
en
charge the battery. Failure to observe these points
may result in damage to the tool. Use of a charger
with batteries other than the specific type(s) for which
it is designed presents a risk of fire.
5.3 Proper organization of the work area
a) Secure the area in which you are working and
take care to avoid directing the beam towards
other persons or towards yourself when setting
up the tool.
b) Avoid unfavorable body positions when working
from ladders. Make sure you work from a safe
stance and stay in balance at all times.
c) Readings taken in the vicinity of reflective objects or
surfaces, through panes of glass or similar materials
may produce incorrect results.
d) Ensure that the tool is set up on a steady, level
surface (not subject to vibration).
e) Use the tool only within its specified limits.
When working in "charging during operation"
f)
mode, attach the AC adapter in a secure posi-
tion, e.g. on a tripod.
g) Use of products for applications different from those
intended could result in hazardous situations. Use
the product and its accessories etc. in accord-
ance with these instructions and in the manner
intended for the particular type of product. Take
6 Before use
NOTE
The tool may be powered only by a Hilti PRA 84 or PRA
84G battery.
6.1 Fitting the battery 2
CAUTION
Before inserting the battery in the tool, check to
ensure that the battery terminals and the contacts in
the tool are free from foreign objects.
1. Push the battery into the tool.
2. Turn the catch in a clockwise direction until the
"locked" symbol appears.
6.2 Removing the battery 2
1. Turn the catch in a counter-clockwise direction until
the "unlocked" symbol appears.
2. Pull the battery out of the tool.
22
All manuals and user guides at all-guides.com
h) Use of the telescopic staff in the vicinity of over-
5.3.1 Electromagnetic compatibility
NOTE
Only for Korea: This device is suitable for the electromag-
netic radiation encountered in residential environments
(Class B). It is intended mainly for use in residential en-
vironments but may also be used in other environments.
Although the tool complies with the strict requirements
of the applicable directives, Hilti cannot entirely rule out
the possibility of the tool being subject to interference
caused by powerful electromagnetic radiation, leading
to incorrect operation. Check the accuracy of the tool
by taking measurements by other means when working
under such conditions or if you are unsure. Likewise, Hilti
cannot rule out the possibility of interference with other
devices (e.g. aircraft navigation equipment).
5.3.2 Laser classification for Laser Class 2/Class II
Depending on the version purchased, the tool com-
plies with Laser Class 2 in accordance with IEC825-
1:2007/EN60825-1:2007 and Class II in accordance with
CFR 21 § 1040 (FDA). This tool may be used without
need for further protective measures. The eyelid clos-
ure reflex protects the eyes when a person looks into
the beam unintentionally for a brief moment. This eyelid
closure reflex, however, may be negatively affected by
medicines, alcohol or drugs. Nevertheless, as with the
sun, one should not look directly into sources of bright
light. Do not direct the laser beam toward persons.
6.3 Charging the battery
DANGER
Use only the Hilti batteries and Hilti AC adapters listed
under "Accessories". Use of tools or AC adapters which
show visible signs of damage is not permissible.
6.3.1 Charging a new battery for the first time
Charge the battery fully before using it for the first time.
NOTE
Make sure the system to be charged is standing securely.
the working conditions and the work to be per-
formed into account.
head high voltage cables is not permissible.
tools