tau K100M Guide D'installation page 6

TAU srl - Via Enrico Fermi, 43 - 36066 Sandrigo (VI) - Italy
Tel +39 0444 750190 - Fax +39 0444 750376 - www.tauitalia.com
22
PAP
Foglietto illustrativo - CARTA - Raccolta differenziata
Segui le indicazioni del tuo comune.
Instruction leaflet - PAPER - Waste separation
Follow the instruction s of your city hall
WARNING!
Attention: This product may only be installed from professional installers. Only qualified and trained electricians may
connect, programme and service the controls.
No information given in this manual can be considered as being of interest to end users.
This manual is enclosed with control unit K100M and may therefore not be used for different products!
Important information:
Disconnect electric power to the system before making maintenance, repairs or removing covers
The K100M control unit has been designed to control a electromechanical sliding door operator.
Any other use is considered improper and is consequently forbidden by current laws.
Read all instructions carefully and completely before attempting to install and use this automatic gate operator!
INSTALLATION
Make sure the gate has been properly installed and slides freely in both directions. Repair or replace all worn or damaged
gate hardware prior to installation. A freely moving gate will require less force to operate and will enhance the performance
of the operator and safety devices used with the system.
Also check that the gate operator assembly has been installed according to the instructions.
Check that the gate slides freely on a horizontal plane (gates that open / close on sloping floors can affect the operation and
duration of the control unit and the gearmotor).
WARNING: The automatic gate operator must be grounded - All Federal, State and local safety codes must be observed.
ATTENTION:
- do not use solid wire, use only multi threaded wire
- do not reuse pre-existing electric wire.
IF THE ABOVE INSTRUCTIONS ARE NOT FOLLOWED THE "MANUFACTURER" SHALL IN NO EVENT BE LIABLE FOR DIRECT, INDI-
RECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS WHETHER BASED IN CONTRACT TORT OR
ANY OTHER LEGAL THEORY DURING THE COURSE OF THE WARRANTY OR AT ANY TIME THEREAFTER.
CONTROL PANEL FOR ONE 230 V AC MOTOR
MICROPROCESSOR-CONTROLLED LOGIC

STATUS LEDS

LINE FUSE

BUILT-IN FLASHING LIGHT CIRCUIT

BUILT-IN 433.92 MHz RADIO RECEIVER

MAX. OPERATING TIME 96"

AUTOMATIC 50 / 60 HZ FREQUENCY DETECTION

ADJUSTABLE SOFT-STOP

AMPEROMETRIC OBSTACLE DETECTION

• COMPATIBILITY WITH OUR APPS: TAUOPEN AND TAUAPP
ATTENTION:
- In case of long sections of cables (> 20 m) for N.O./N.C. controls (e.g. OPEN / CLOSE, STOP, PEDESTRIAN, etc.), in order to
avoid gate malfunctions, it will be necessary to uncouple the various controls using RELAYS or using our 750T-RELE devi-
ce.
TESTING
Once the connection has been completed:
 All the green LEDs must be ON (each of them corresponds to a Normally Closed input). They will turn OFF when the controls
to which they are associated are operated.
 The opening control red LED must be switched OFF (corresponding to a Normally Open input), it comes ON only when the
control it is associated with is involved; the DL1 red LED must be steady ON.
TECHNICAL CHARACTERISTICS
Power input – control board
Nominal power
230 V AC Input protection fast blow fuse (F1 - 5x20)
Power input – motors
Power input – auxiliary circuits
24 V AC Input (auxiliary circuits) fast blow fuse (F2 - 5x20)
Working temperature
Protection degree
K100M
Control panel for T-ONE5E gearmotor
D-MNL0K100M
16-03-2022 - Rev.17
INSTALLATION GUIDE
230 V AC - 50-60 Hz
400 W
F 3,15 A
230 V AC
24 V AC
F 500 mA
-20°C ÷ +55°C
IP 44
FW. 8.xx
English