DeWalt D25501 Traduction De La Notice D'instructions Originale page 21

5) Service
a ) Have your power tool serviced by a qualified repair person
using only identical replacement parts. This will ensure that the
safety of the power tool is maintained.
Additional Safety Instructions for Rotary Hammers
Wear ear protectors. Exposure to noise can cause hearing loss.
•
• Use auxiliary handle
cause personal injury.
• Hold power tool by insulated gripping surfaces, when performing
an operation where the cutting accessory may contact hidden
wiring or its own cord. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live" and could
give the operator an electric shock.

WARNING: We recommend the use of a residual current device with a
residual current rating of 30mA or less.
Residual Risks
In spite of the application of the relevant safety regulations and the
implementation of safety devices, certain residual risks cannot be avoided.
These are:
• Impairment of hearing.
• Risk of personal injury due to flying particles.
• Risk of burns due to accessories becoming hot during operation.
• Risk of personal injury due to prolonged use.
Electrical Safety
The electric motor has been designed for one voltage only. Always check
that the power supply corresponds to the voltage on the rating plate.
Your D WALT tool is double insulated in accordance with
e
EN60745; therefore no earth wire is required.

WARNING: 115 V units have to be operated via a fail-safe isolating
transformer with an earth screen between the primary and
secondary winding.
If the supply cord is damaged, it must be replaced by a specially prepared
cord available through the D
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the old plug.
• Connect the brown lead to the live terminal in the plug.
• Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless absolutely necessary. Use an
approved extension cable suitable for the power input of your charger (see
Technical Data). The minimum conductor size is 1.5 mm
length is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Rotary hammer (D25501, D25601, D25602, D25603)
or
1 Chipping hammer (D25820, D25831)
1 Side handle
1 Kitbox (K-models only)
1 Instruction manual
Downloaded from www.Manualslib.com
3 , if supplied with the tool. Loss of control can
WALT service organisation.
e
2 ; the maximum
manuals search engine
• Check for damage to the tool, parts or accessories which may have
occurred during transport.
• Take the time to thoroughly read and understand this manual prior
to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Clutch Setting 40 Nm is designed for most drilling applications.
Clutch Setting 80 Nm is designed for higher
torque applications.
Red service indicator LED. For detailed description see under
Service Indicator LED's.
Yellow service indicator LED. For detailed description see under
Service Indicator LED's.
Visible radiation. Do not stare into light.
Date Code Position (Fig. A)
The date code 23 , which also includes the year of manufacture, is printed
into the housing.
Example:
2016 XX XX
Year of Manufacture
Description (Fig. A, B)

WARNING: Never modify the power tool or any part of it. Damage or
personal injury could result.
Trigger switch (D25501, D25601, D25602, D25603)
1
On/off rocker switch (D25820, D25831)
Lock-on slider (D25601, D25602, D25603)
2
Side handle
3
Main handle
4
Active vibration control (D25601, D25602, D25603, D25831)
5
6 Mode selector switch
Electronic speed and impact control dial (D25601, D25602, D25603,
7
D25831)
Clamp wheel
8
Side handle clamp
9
Steel ring
10
Bush
11
Tool holder
12
Locking sleeve
13
14 Pin
Collar
15
Side handle knob
16
Intended Use
The D25501, D25601, D25602, D25603 rotary hammers have been designed
for professional rotary drilling and chipping applications.
EngLIsH
19