Options And Accessories - Hatco MVW Série Manuel D'installation Et D'utilisation

OPTIONS AND ACCESSORIES

Wall Mount Kit
The mini Vertical Warmer wall mount kit includes hardware for
wood stud installation or hollow wall installation. Use the
following parts and procedure to mount a mini Vertical Warmer
on a wall.
Parts Included
Item
Wall mount Bracket
mounting Screw
Toggle Bolt, 2" (51 mm)
Washer
Installation Procedure
NOTE: The Mini Vertical Warmer must be fastened to a wall
covered by a minimum of 3/8" thick sheathing.
1. Determine the mounting location for the mini Vertical
Warmer. make sure the mounting location meets the
requirements listed in the INSTaLLaTION section of this
manual.
2. Determine and mark the height for the unit installation.
• There are two mounting holes that are centered and
vertically-aligned on the wall mount bracket. mark the
wall height where the top, center of the unit should be
located.
3. measure down 3/4" (18 mm) from the unit height mark
made in the previous step, and mark the top mounting hole
location.
4. Using a level and tape measure, measure down 11"
(279 mm) from the top mounting hole location. mark the
bottom mounting hole location, making sure that it is
vertically aligned with the top mounting hole.
Slip bracket holes
over hinge screws.
Snap bracket
underneath
cutout.
Wall Mount Bracket
attaching the Wall Brackets
5. Locate the wood stud positions in the wall.
• If the mounting location aligns with a wood stud position,
go to step 6.
• If the mounting location does not align with a wood stud
position, go to step 7 for hollow wall installation.
Quantity
1
2
2
2
11"
(279 mm)
6. For wood stud installation, install the included mounting
screws into the wall at each marked location, leaving the
head of the screw out from the wall a distance of 1/16"
(1.5 mm).
7. For hollow wall installation, install the included toggle bolts
with washers into the wall.
a. Drill a 1/2" (13 mm) pilot hole in the wall at each marked
location.
b. Remove the wing section from each included toggle bolt
and place one of the included washers on each bolt.
c. Thread the wing section back onto each toggle bolt
approximately one quarter of the length of the bolt. The
wing tips should be pointing toward the head of the bolt.
d. Squeezing the wing tips together, insert each toggle bolt
into the pre-drilled pilot holes in the wall until the wing
tips spring out on the opposite side of the wall.
e. Tighten each toggle bolt until the washer against the
head of the bolt is out from the wall a distance of 1/16"
(1.5 mm).
8. Install the wall mount bracket onto the back of the unit.
• Pull out slightly on each side of the bracket and slip the
holes on the bracket over the flip-up door hinge screws.
• Snap the bottom of the bracket underneath the cutout at
the bottom of the unit.
9. Lift the unit and hook the two mounting holes on the wall
mount bracket over the corresponding mounting
screws/toggle bolts in the wall. make sure the bracket on
the unit is fully seated on the mounting screws/toggle bolts.
• The washers on the toggle bolts should be positioned on
the wall side of the bracket.
Jumper Power Cord
a 2' (610 mm) jumper power cord
is available as an accessory that
provides a power connection
from one mini Vertical Warmer to
another. a total of eight units can
be connected together off of one
electrical receptacle. The male
plug on the jumper cord connects
to the power outlet on the
upstream unit, and the female plug connects to the power inlet
on the downstream unit. Each unit remains independently-
controlled.
Power
Cord
Installing a Jumper Power Cord
10
English
Male Plug
Female Plug
Jumper Power
Power
Cord
Outlet
Form No. mVWm-0515
Power
Inlet