Pool Water Chemistry; Installation Instructions - Bestway Flowclear 58215 Manuel De L'utilisateur

PICTURE
1
2
8 9
REF. NO. PARTS NO. DESCRIPTION
1 P6488 Electrolytic Cell
2 P6369 Connecting Hose
3 P6489 Water Flow Sensor
4 P6371 Gasket
5 P6372 Screw
Adaptor E ( For connection to filter
6 P6375
pumps with 1-1/4in.(32mm) hose size)
Adaptor F ( For connection to filter
7 P6376
pumps with 1-1/4in.(32mm) hose size)
8 Adaptor A
F6H184
9 Adaptor B

POOL WATER CHEMISTRY

Optimum Pool Water Chemistry Conditions
It is recommended that the following pool water chemistry
conditions should be maintained to help protect pool users.
The chlorinator is warranted to operate properly only if below
conditions are met.
Minimum
Free Chlorine 0
Combined Chlorine 0
pH 7.2
Total Alkalinity 100ppm
Calcium Hardness 150ppm
Stabilizer (Cyanuric Acid) 10ppm
Pool Salt Usage
Use only sodium chloride (NaCl) salt that is at least 99.8% pure.
The ideal salt level in the pool water is between 2000~3000ppm
(parts per million).
Water Capacity (Calculated at
90% for Frame Pool and 80%
Salt Needed for Startup
For Fast Set & Oval Pool)
Gallons Liters Lbs
7500 42
2000
15000 85
4000
22500 130
6000
30000 170
8000
37500 210
10000
45500 255
12000
53000 300
14000
3
4 5
6 7
Ideal Maximum
1.0-3.0ppm 3.0ppm
0 0.2ppm
7.4 - 7.6 7.8
100 - 140ppm 140ppm
200 - 400ppm 500 - 1000ppm
30 - 50ppm 150ppm
Salt Needed when Low Salt
Detected
Kgs Lbs
20 15 6
40 25 10
60 40 20
75 55 25
95 65 30
115 80 35
135 95 40
Salt Calculation for Pools
Salt Needed for Startup
Lbs
Water Capacity
(Gallons) x 0.0375
Operating Time Reference
Water Capacity
Gallons Liters
2000
4000 15000
6000 22500
8000 30000
10000 37500
12000 45500
14000 53000
QTY.

INSTALLATION INSTRUCTIONS

1
NOTE: The preferred installation is that the chlorinator must be
1
installed as the last piece of pool equipment in the return line to
(100cm)
the pool. This will extend the life of the titanium plates and
1
maintain its performance.
1. If your above ground pool is filled with water, remove the
1
debris screens from the inside of the pool and insert the
1
stopper plugs in the pool's inlet and outlet valves before the
chlorinator installation (or close the control valves), which will
1
prevent water from flowing out of the pool. Jump to step 2
directly if your pool is empty.
1
2. Connect the adaptor F to the electrolytic cell outlet and screw
the threaded locking ring into position.
1
3. Disconnect the water return (to the pool) hose from the filter
1
pump connection, and connect this hose to the adaptor F with
a hose clamp.
4. Connect the adaptor E to the filter pump outlet and screw the
threaded locking ring into position.
5. Connect the connecting hose to the adaptor E and screw the
threaded locking ring into position.
6. Remove the stopper plugs and insert the debris screens (or
open the control valves) to allow water to flow.
For connection to filter pumps with 1-1/4in. (32mm) hose
(with hose clamps):
A
Connecting Hose
Kgs
Adaptor F
4
Salt Needed when Low Salt Detected
Kgs Lbs
Water Capacity Water Capacity
(Liters) x 0.0045 (Gallons) x 0.0067
Operating Time (hours) at different
ambient/air temperatures
10-19°C 20-28°C
(50-66°F) (68-82°F)
7500 1 1
2 2
2 4
4 6
4 6
6 8
6 8
Pool
B
Filter
Pump
Kgs
Water Capacity
(Liters) x 0.0008
29-35°C
(84-95°F)
2
4
6
8
8
10
10
Adaptor E
S-S-004379