Introduction; Specifications; Parts Reference - Bestway Flowclear 58215 Manuel De L'utilisateur

flow around the pool.
NOTE: Atmospheric conditions may affect
the performance and life span of this
product. Unnecessary wear and tear may
occur during periods of cold, heat and
exposure to sun. Whenever possible shelter
this product from these conditions.
NOTE: Assembly and disassembly of this
product should only be performed by adults.
WARNING: If the supply cord is damaged, it
must be replaced by the manufacturer, its
service agent or similarly qualified persons
in order to avoid a hazard.
WARNING: Electric installations should
follow national wiring rules, consult a
qualified electrician with any questions.
WARNING: This appliance is not intended
for use by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of
the appliance by a person responsible for
their safety.
Children should be supervised to ensure
that they do not play with the appliance.
• CSA ENCLOSURE 3
• FOR USE WITH SWIMMING POOLS
ONLY.
• CAUTION: TO ENSURE CONTINUED
PROTECTION AGAINST SHOCK
HAZARD, USE ONLY IDENTICAL
REPLACEMENT PARTS WHEN
SERVICING.
• WARNING: RISK OF ELECTRIC SHOCK.
CONNECT ONLY TO A GROUNDING
TYPE RECEPTACLE.
• CAUTION: THIS PRODUCT IS FOR USE
WITH STORABLE POOLS ONLY - DO
NOT USE WITH
PERMANENTLY-INSTALLED POOLS.
• CAUTION: CONNECT ONLY TO
GROUNDING TYPE RECEPTACLE
PROTECTED BY A CLASS A GROUND
FAULT CIRCUIT INTERRUPTER.
• CAUTION: FOR CONTINUED
PROTECTION AGAINST POSSIBLE
ELECTRIC SHOCK THIS UNIT IS TO BE
MOUNTED TO THE BASE IN
ACCORDANCE WITH THE
INSTALLATION INSTRUCTIONS.
• WARNING – RISK OF ELECTROCUTION
1) Connect Only To Properly Grounded
Outlet. Do Not Remove Ground Pin
2) Inspect Cord Before Using – Do Not Use
If Cord Is Damaged.
3) Keep Ground-Fault Circuit-Interrupter Dry
And Off The Ground
4) Do Not Touch Plug With Wet Hands
5) Double Insulated – When Servicing Use
Only Identical Replacement Parts.
6) Read Instruction Manual Before Using.
DO NOT REMOVE THIS TAG
SAVE THESE INSTRUCTIONS.

INTRODUCTION

Common salt (sodium chloride) is made up of two elements,
sodium and chloride. During the installation of your chlorinator, a
measured quantity of salt is dissolved in the pool water to create
a mild saline solution. As part of the daily filtration cycle, the pool
water is passed through the chlorinator's electrolytic cell to
produce chlorine which is dissolved instantly in the water. In
simple, non-technical terms, the chlorine instantly starts to
destroy bacteria, algae and oxidizes other organic materials.
Control Panel
Power Cord
• Electrolytic Cell (with Titanium Plates)
The electrolytic cell contains bipolar titanium electrodes which
perform the electrolysis and produce chlorine when energized
with DC current. Chlorine is generated as pool water containing
salt passes through the cell.
• Flow Sensor
The flow sensor protects the electrolytic cell and assures there
will always be adequate water flowing through the cell.
• Control Panel
The chlorinator includes a electronic control panel with buttons
and LED indicators to control the chlorinator and produce
chlorine at the defined operating hours.

SPECIFICATIONS

Rated Voltage:
Electrolytic Cell Working Voltage:
Wattage:
Maximum Chlorine Output/hour:
Flow Rate Range:
Recommended Salt Level:
Water temperature
Ambient temperature

PARTS REFERENCE

Before assembly, take a few
minutes to become familiar
with all the parts.
NOTE: Drawings for
illustration purpose
only. May not reflect
actual product.
Not to scale.
3
Electrolytic Cell
Electrolytic Cell Line Cord
Flow Sensor
110-120V AC
14V DC
1.5A
12 grams/hour
700~4000gallons/hour (2650~15140L/h)
2500 ppm (2.5g/L)
10-35°C (50-95°F)
5-40°C (41-104°F)
7
Water Inlet
6
2
S-S-004379