MSW Motor Technics MSW-TRB-300 Manuel D'utilisation page 5

g) The material to be worked should be free of impurities.
h) Do not touch movable parts or accessories during
device operation.
i) Use protective gloves to avoid being hurt by sharp
edges.
j) Do not work elements made of hard materials.
k) It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
2.3. SAFE DEVICE USE
a) Do not overload the device. Use appropriate tools for
the given task. A correctly selected device will perform
the task for which it was designed better and in a safer
manner.
b) When not in use, store in a safe place, away from
children and people not familiar with the device, who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
c) Maintain the device in a good technical state. Before
each use check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of
the device. If damage is discovered, hand over the
device for repair before use.
d) Keep the device out of the reach of children.
e) Device repair or maintenance should be carried out by
qualified persons, only using original spare parts. This
will ensure safe use.
f) To ensure the operational integrity of the device, do
not remove factory fitted guards and do not loosen
any screws.
g) When transporting and handling the device between
the warehouse and the destination, take into account
the occupational health and safety principles for
manual transport operations which apply in the
country
h) Use the device to work elements of parameters
conforming with the data given in the technical data
table. Do not exceed the permissible dimensions of
the worked material.
i) Do not work two workpieces at the same time.
j) Long workpieces must be supported and set stably
for working.
k) Mount the device on a stable, dry and flat surface
of a size that is adapted to the device and worked
material overall dimensions.
l) The floor at the workstation should be anti-slip
ATTENTION! Despite the safe design of the device
and its protective features, and despite the use of
additional elements protecting the operator, there
is still a slight risk of accident or injury when using
the device. Stay alert and use common sense when
using the device.
3. USE GUIDELINES
A bending machine is a device designed for manual
bending of metal elements.
The user is liable for any damage resulting from
unintended use of the device.
8
3.1. DEVICE DESCRIPTION
1 2
3
4
6 5
7
1. Frame main
2. Swivel arm frame
3. Handle (applied to a 1'x2 'rectangular element)
4. Matrix
5. Fixing block
6. Bending element
7. Stand with mounting holes
12 13
11
14
10
15
9
8
8. Belt
9. Matrix flange
10. Belt attachment pin
11. Pin 1''
12. Pin 7/8''
13. Mounting block pin
14. Screws ¾''
15. Screws ½''
3.2. PREPARING FOR USE
ASSEMBLING THE DEVICE
CAUTION: The device can be mounted on a work table or stand.
Main frame installation
2
3
4
1
5
1. Make sure that both frame plates are aligned in the
same direction.
2. Install and lubricate pin 1 ''. Make sure it moves
smoothly up and down.
3. Tighten the screws ¾ 'thoroughly so that the arm can
be moved under pressure.
Rev. 06.07.2020
4. Move the 1 'x 2' rectangular element over the handle
to move the lever.
5. Center the handle, then tighten the flange.
Swivel arm installation
7
6
8
9
11
10
6. Remove pin 1 '' from the main frame and insert into
the holes of the swing arm frame as shown.
7. Insert pin 7/8 '' according to the drawing.
8. Secure the swivel arm frame plates with screws ½ '.
9. Make sure not to use pads under the nuts on the
bottom or on the top of the screws.
10. Check that the screws are tightened securely.
11. The spacers have dimensions 1/2 '' x 2 5/8 ''
13
12
12. Remove pin 1 '', insert the swivel arm frame into
the main frame, align the holes and insert pin 1 '' as
shown.
13. Align the swivel arm with the holes in the main frame.
Matrix installation
14 15
14. Pull out pin 1 '' and pin 7/8 '' in the frame of the swivel
arm, place the matrix, insert pin 1 '' into the frame
holes and the matrix sleeve.
15. Insert pin 7/8 '' into the swivel arm frame and the first
matrix hole.
Rev. 06.07.2020
Installation of the pipe and mounting block
16
17
16. Close the swivel arm and place the pipe in the matrix
as shown.
17. Insert the mounting block as shown and secure with
the pin.
Belt and pin installation
18
18 Place the belt around the pipe, stretch it and put the
pin through the belt and the matrix.
3.3. DEVICE USE
Caution: Before starting work, make sure that the places
marked in the figure below are well lubricated. At the same
time, make sure that grease does not get to other places
on the device.
Bending instructions:
1. Pull the handle according to the arrow in the drawing.
9