Télécharger Imprimer la page
Ryobi PRO CUT II AC04141B Guide Rapide
Ryobi PRO CUT II AC04141B Guide Rapide

Ryobi PRO CUT II AC04141B Guide Rapide

Tête universelle à ligne de coupe

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

WARNING:
To reduce the risk of injury, user must read and under-
stand the operator's manual for their string trimmer and
this instruction sheet. Always wear eye protection marked
to comply with Z87.1 Ensure compatibility and fit before
using this accessory. Do not use this accessory if a part
is damaged or missing.
When using RYOBI and HOMELITE string trimmers, no
adaptors are needed. For other brands, see the Adaptor
Chart for the proper hardware configuration needed to
use the Universal PRO CUT II
trimmer.
WARNING:
Failure to use the correct adaptor, nut, and spool retainer
combination for your trimmer could cause the string head
to detach from your trimmer and result in serious personal
injury and/or property damage.
INSTALLING STRING HEAD
See Figure 1.
 Stop the engine and disconnect the spark plug wire.
 Following the instructions in the operator's manual for
your string trimmer, remove the old string head.
 Install the string head on the drive shaft until fully seated.
 Install the spool retainer and tighten securely.
 Install string as described in the next section.
INSTALLING STRING
See Figure 2.
Use monofilament string between .095 in. and .105 in.
diameter. Use original manufacturer's replacement string
for best performance.
 Stop the engine and disconnect the spark plug wire.
 Gather two of the pre-cut lengths of trimmer line provided
or cut two pieces of trimmer line, in 11 in. lengths.
 Insert the strings into the slots located on the sides of the
string head. String should be pushed in until approximately
1 in. protrudes from the holes on the top of the string
head.
 Remove old string by pulling it from the holes located on
the top of the string head.
991000971
6-8-16 (REV:01)
UNIVERSAL PRO CUT II
STRING HEAD
AC04141B
String Head with your
TECHTRONIC INDUSTRIES POWER EQUIPMENT
Anderson, SC 29625, USA
PULL STRINGS
FROM HOLES
TO REMOVE
WARNING:
Do not remove screws or disassemble head. If head is
opened, compression springs may fly out toward operator
and result in serious injury.
1428 Pearman Dairy Road
Phone 1-800-860-4050
www.ryobitools.com
INSERT STRINGS THROUGH SLOTS UNTIL
APPROX. 1 IN. PROTRUDES FROM HOLES
HOLE
SLOT
DRIVE SHAFT
STRING
HEAD
SPOOL
RETAINER
Fig. 1
SLOT
HOLE
Fig. 2

Publicité

loading

Sommaire des Matières pour Ryobi PRO CUT II AC04141B

  • Page 1 STRING HEAD using this accessory. Do not use this accessory if a part is damaged or missing. When using RYOBI and HOMELITE string trimmers, no SPOOL adaptors are needed. For other brands, see the Adaptor RETAINER Chart for the proper hardware configuration needed to...
  • Page 2 USING THE ADAPTORS Along with the Pro Cut II String Head Assembly and pre-cut trimmer line, this package includes the items below, which ™ may be used to adapt the string head for use on the trimmers listed in the Adaptor Chart below. Universal Washer Thread...
  • Page 3 Ne pas utiliser cet accessoire si des pièces sont endommagées ou manquantes. RETENUE DE BOBINE Les taille-bordures de marque RYOBI ou HOMELITE ne requièrent aucun adaptateur. Pour les autres marques, consulter le tableau « Adaptateurs » afin de connaître la configuration matérielle adéquate pour utiliser la tête de Fig.
  • Page 4 UTILISATION DES ADAPTEURS En plus de l’ensemble de tête de coupe Pro Cut II et du fil pour taille-bordures précoupé, cet ensemble comprend les ™ éléments présentés ci-dessous, qui peuvent être utilisés pour adapter la tête de coupe aux taille-bordures spécifiés au tableau «...
  • Page 5 No use este accesorio si está dañado o si falta alguna pieza. RETÉN DEL Cuando se utilizan las recortadoras de hilo RYOBI y CARRETE HOMELITE, no se requieren adaptadores. Para otras marcas, consulte la tabla de adaptadores para obtener la configuración de hardware requerida para poder...
  • Page 6 USO DE ADAPTADORES Además del conjunto del cabezal de hilo Pro Cut II y la línea precortada de la recortadora, este paquete incluye los artículos ™ que se mencionan a continuación, los cuales pueden utilizarse para adaptar el cabezal de hilo a las recortadoras que se incluyen en la tabla de adaptadores.