Briteq BEAM WIZARD5x5 Mode D'emploi page 9

ENGLISH
[SET CONFIG > CHAN. Mode]
Used to set the desired channel mode.
 Press the ▲/▼/◄/► buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼ buttons to select the desired mode:
 12 CH mode: [PAN/TILT] + RGBW+Dim+strobe+sound for all 25pixels together.
 18 CH mode: same as the 12CH mode but with additional RGBW-effects library control.
 110 CH mode: full control over all functions, including RGBW-control for all 25pixels separately.
 116 CH mode: same as the 110CH mode but with additional RGBW-effects library control.
 Once the correct option shows on the display, press the [ENTER] button to confirm.
[SET CONFIG > SHOW Config] –
All functions in this level are related to the automatic shows.
[NO DMX Mode]
Used to set how the projector reacts when the DMX-signal disappears.
 Press the ▲/▼/◄/► buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼ buttons to select the desired mode:
 BLACKOUT: output turns black while no DMX is detected.
 FREEZE: output based on the last valid DMX-signal is kept on the projector.
 AUDIO: the projector starts working in audio mode.
 Once the correct option shows on the display, press the [ENTER] button to confirm.
Note: as soon as the input detects a DMX-signal, blackout, freeze or audio mode will be cancelled.
[Install POS]
Used to select the installation position of the projector while used in standalone mode.
 Press the ▲/▼/◄/► buttons until the desired function is showing on the display.
 Press the [ENTER] button to start editing.
 Use the ▼/▲ buttons to select one of the available installation positions:
 [Floor 180°]: Fixture is placed on the floor. [PAN/TILT] movements are not limited.
 [CeilingHung]: Fixture is fixed on the ceiling. [TILT] movements are limited to ±60°.
 [Stage Floor]: Fixture is placed on a stage, in front of the audience. The spot is always projecting
towards the audience's direction; i.e. in front of the stage. [PAN] movement angle (left to right to left):
160°. [TILT] movement angle: 90° (60° above horizon; 30° below horizon.)
 [Stage Hung]: Fixture is fixed upside-down on the ceiling of a stage. The spot is mainly projecting
towards the audience in front of the stage. [PAN] movement angle (left to right to left):160°. [TILT]
movement angle: 90° (vertically, front 75°; back 15°)
 Once the right mode is shown on the display, press the [ENTER] button to confirm.
[SET CONFIG > MATRIX Set] –
All functions in this level are related to the 5x5 LED-Matrix panel.
[LedBehavior]
Used to select the reaction time of the projector.
 Press the ▲/▼/◄/► buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼ buttons to select the desired mode:
 LED
 HALOGEN
 Once the correct option shows on the display, press the [ENTER] button to confirm.
[DIM Curve]
Used to set the dimmer curve of the master dimmer.
 Press the ▲/▼/◄/► buttons until the desired function is showing on the display.
 Press the [ENTER] button: the values can be changed
 Use ▲/▼ buttons to selected the desired curve:
BRITEQ
®
The projector follows the instructions instantly, no delay.
The projector imitates the behavior of a halogen lamp (slower reaction time).
7/107
OPERATION MANUAL
BEAM WIZARD5x5-RGBW