Publicité
Les langues disponibles
Les langues disponibles
power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool's operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
5) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR PLANERS
GENERAL
•
This tool should not be used by people under the age of
16 years
•
The noise level when working can exceed 85 dB(A);
wear ear protection
•
Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
•
Certain kinds of dust are classified as carcinogenic
(such as oak and beech dust) especially in conjunction
with additives for wood conditioning; wear a dust
mask and work with a dust extraction device when
connectable
•
Follow the dust-related national requirements for the
materials you want to work with
SKIL can assure flawless functioning of the tool only
•
when original accessories are used
•
Never use the tool when cord is damaged; have it
replaced by a qualified person
•
Always disconnect plug from power source before
making any adjustment or changing any accessory
BEFORE USE
•
Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool (tools with
a rating of 230V or 240V can also be connected to a
220V supply)
•
Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
•
Before using the tool check that the knives do not brush
anywhere
•
Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
•
Use clamps or another practical way to secure and
support the workpiece to a stable platform (holding
the workpiece by hand or against your body leaves it
unstable and may lead to loss of control)
DURING USE
•
Hold the power tool by insulated gripping surfaces,
because the cutter may contact its own cord (cutting
a "live" wire may make exposed metal parts of the power
tool "live"and shock the operator)
•
Always keep the cord away from moving parts of the tool;
direct the cord to the rear, away from the tool
•
Keep your fingers away from the rotating knives
•
In case of electrical or mechanical malfunction,
immediately switch off the tool and disconnect the plug
•
If the cord is damaged or cut through while working, do
not touch the cord, but immediately disconnect the plug
If any chip should get jammed in the chip outlet, you
•
should switch off the motor, ensure that all moving parts
have come to a complete standstill, disconnect the plug,
and remove the jammed chip
AFTER USE
•
Wait for the cutter to stop before setting the tool
down (an exposed rotating cutter may engage the
surface leading to possible loss of control and serious
injury)
EXPLANATION OF SYMBOLS ON TOOL
3 Read the instruction manual before use
4 Double insulation (no earth wire required)
5 Do not dispose of the tool together with household waste
material
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
•
Do not connect the blue (= neutral) or brown (= live) wire
in the cord of this tool to the earth terminal of the plug
•
If for any reason the old plug is cut off the cord of this
tool, it must be disposed of safely and not left unattended
USE
•
Changing/reversing knives 6
This planer is equipped with non-grindable knives with
cutting edges on both sides; so if one side has become
blunt, the other side can be used
! switch off the tool and disconnect the plug
- take wrench from storage A
- turn tool upside down
- loosen 3 bolts B with wrench (do not remove bolts)
- push knife out of cutter block with piece of wood
- put knife back in cutter block in reversed position, or
use new knife
! groove in knife should match ledge in cutter block
! both knife ends should protrude equally
- firmly tighten 3 bolts B with wrench
! change/reverse knives in time; only use sharp
knives
! always change/reverse both knives at the same
time
! do not attempt to adjust the knives with
cutter block screws C, which are pre-set at
manufacturing
•
Adjusting planing depth 7
- turn knob D in "+"/"-" direction for increasing/
decreasing planing depth
- use indicator E as reference
8
Publicité
