Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
Troubleshooting
If a problem should arise, first check the following.
1. Are the connections correct?
2. Have you operated the receiver according to the operating instructions?
3. Are the speakers, turntable and other components operating properly?
If this unit is not operating properly, check the items listed in the table below. Should the problem
persist, there may be a malfunction. Disconnect the power immediately and contact your store of
purchase.
Symptom
Cause
• Power supply cord not plugged in
Display not lit and
securely.
sound not produced
when POWER switch
set to on.
• Speaker
cables
connected.
• Improper setting of the FUNCTION
knob.
Display lit but sound
• Volume control set to minimum.
not produced.
• MUTING is on.
• Digital signals not input. Digital
input selected.
• Speaker
terminals
circuited.
• The ventilation holes of the set are
blocked.
Display not lit and
power indicator is
flashing rapidly.
• The unit is operating at continuous
high power conditions and/or with
inadequate ventilation.
• Incomplete connection of speaker
Sound produced only
cables.
from one channel.
• Incomplete
input/output cables.
Positions of
• Reverse connections of left and
instruments reversed
right speakers or left and right
during stereo playback.
input/output cables.
Measures
• Check the insertion of the power
supply cord plug.
• Turn the power on with the remote
control unit after turning the
POWER switch on.
not
securely
• Connect securely.
• Set to a suitable position.
• Turn volume up to suitable level.
• Switch off MUTING.
• Input digital signals or select input
terminals to which digital signals
are being input.
are
short-
• Switch
power
off,
connect
speakers properly, then switch
power back on.
• Turn off the set's power, then
ventilate it well and allow it to cool
down.
Once the set has cooled down,
turn the power back on.
• Turn off the set's power, then
ventilate it well and allow it to cool
down.
Once the set has cooled down,
turn the power back on.
• Connect securely.
connection
of
• Connect securely.
• Check left and right connections.
Symptom
• Ground wire of turntable not
connected properly.
Humming noise
• Incomplete
produced when record
connection.
is playing.
• TV or radio transmission antenna
nearby.
• Turntable and speaker systems too
close together.
Howling noise
• Floor is unstable and vibrates
produced when
easily.
volume is high.
Page
16
• Stylus pressure too weak.
8
Sound is distorted.
• Dust or dirt on stylus.
• Cartridge defective.
• MC cartridge being used.
6
Volume is weak.
17
• Batteries dead.
17
• Remote control unit too far from
17
This unit does not
this unit.
18, 19
operate properly when
• Obstacle between this unit and
remote control unit is
remote control unit.
used.
• Different button is being pressed.
<
•
and
5, 6
inserted in reverse.
2, 5
2, 5
5, 6
5 ~ 7,
11 ~ 16
6
47
ENGLISH
Cause
Measures
• Connect securely.
PHONO
jack
• Connect securely.
• Contact your store of purchase.
• Separate as much as possible.
• Use cushions to absorb speaker
vibrations transmitted by floor. If
turntable is not equipped with
insulators, use audio insulators
(sold separately).
• Apply proper stylus pressure.
• Check stylus.
• Replace cartridge.
• Replace with MM cartridge or use
a
head
amplifier
transformer.
• Replace with new batteries.
• Move closer.
• Remove obstacle.
• Press the proper button.
>
ends of batteries
• Insert batteries properly.
Troubleshooting
Page
15
15
—
—
—
—
—
—
15
or
step-up
3
3
3
—
3
Publicité
