Shredder Capacity; Emptying The Receptacle; Cautions For Operating; Malfunctions - Intimus 34 CP7 Instructions D'opération

GB
„ When the basket becomes full, the bin full LED
(Fig. 1/5) will light up. The shredder will remain
inoperable until the wastebasket is emptied
(3.4 „Emptying the receptacle").

3 .3 Shredder capacity

The intimus 34 CP7 will shred up to five sheets paper
and will accept widths up to 220 mm. When shredding
small material like envelopes, receipts insert them in
the middle of the feed opening (Fig. 1/8).

3 .4 Emptying the receptacle

The intimus 34 CP7 is equipped with an electronic
basket full sensor. When the wastebasket becomes
full, the BIN FULL LED (Fig. 1/5) will then illuminate.
Proceed as follows:
1 . Remove the receptacle from in front of the machi-
ne and empty its contents.
2 . Replace the empty receptacle under the machine
and push all the way to the back.
NOTE!
The machine will only run when the receptacle
is pushed completely into the machine!

3 .5 Cautions for operating

Caution!
Damage to the machine!
Ì When manually changing feed direction,
pause long enough for the motor to stop.
Ì Always turn off or unplug the shredder
prior to moving, cleaning or emptying the
wastebasket.
Ì Empty the wastebasket frequently to avoid
possible paper jams caused by shredded
material being pulled back into the cutter
assembly.
Ì Always limit continuous shredding to the
specified time as suggested in the instruc-
tion manual
94651 1 11/17
4

Malfunctions

Caution!
Danger of injury!
Be sure to keep fingers and any personal
effects away from the throat of the feed
opening while the shredder cutters are in
motion.

4 .1 Motor overload

The intimus 34 CP7 is equipped with an automatic
motor overload protection circuit. The duty cycle for
the intimus 34 CP7 is rated for 30 Min. ON / 30 Min.
OFF. The intimus 34 CP7 will automatically terminate
power in case of the following abnormal situations:
„ Operating the shredder at the maximum 5 -sheet
capacity continuously for a prolonged period of
time.
„ Exceeding the shredding capacity, eg. inserting
more than five sheets paper in one pass, or if the
paper is not fed squarely into the feed opening.
Both abnormal operations may result in the activation
of the automatic thermal motor overload protection
circuit, which terminates the power to the shredde.r
A paper jam could cause the thermal motor overload
protection to terminate AC power to the motor. Never
allow the shredder to remain in a jammed condition
with the AC power turned on.
lf this occurs you should:

4 .2 In case of a minor paper jam

In case of a minor paper jam the overload LED
(Fig. 1/4) will light up.
1 . Grasp the excess paper from the top and pull it out
as you depress the REVERSE button (Fig. 1/6). Be
careful not to place your fingers near the feed ope-
ning or else serious harm could result.
2 . Make sure that all of the excess paper has been re-
moved from the feed opening.
3 . You are now ready to resume normal shredding.

4 .3 In case of a major paper jam

In case of a major paper jam the overheat LED (Fig. 1/3)
will light up.
1 . Turn off or unplug the power cord from the AC
outlet and wait at least 30 minutes for the thermal
overload protection to reset.
2 . Plug in the AC power cord and depress the ON/
OFF button (Fig. 1/1).
3 . lf paper was left inside the feed opening prior to
the overload, press the REVERSE button (Fig. 1/6)
34 CP7
9