Machine-Related Safety Instructions - Festool TS 55 REQ Guide D'utilisation

finger on the switch or energising power tools
that have the switch on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
e. Do not overreach. Keep proper footing and bal-
ance at all times. This enables better control of
the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
h. Do not let familiarity gained from freuquent use
of tools allow you to become complacent and ig-
nore, tool safety principles. A careless action
can cause severe injury within a fraction of a sec-
ond.
4 POWER TOOL USE AND CARE
a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
c. Disconnect the plug from the power source and/
or battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power
tool accidentally.
d. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the pow-
er tool's operation. If damaged, have the power
8
tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc. in accordance with these instructions tak-
ing into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
h. Keep handles dry, clean and free from oil and
grease. Slippery handles do not allow for safe
handling and control of the tool in unexpected
situations.
5 SERVICE
a. Have your power tool serviced by a qualified re-
pair person using only identical replacement
parts. This will ensure that the safety of the pow-
er tool is maintained.

Machine-related safety instructions

Cutting procedures
a. DANGER! Keep hands away from cutting
area and the blade. Keep your second hand on
auxiliary handle, or motor housing.
hands are holding the saw, they cannot be cut by
the blade.
b. Do not reach underneath the workpiece. The
guard cannot protect you from the blade below
the workpiece.
c. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade
teeth should be visible below the workpiece.
d. Never hold the workpiece in your hands or
across your leg while cutting. Secure the work-
piece to a stable platform. It is important to sup-
port the work properly to minimize body
exposure, blade binding, or loss of control.
e. Hold the power tool by insulated gripping sur-
faces [1-1] + [1-6], when performing an opera-
tion where the cutting tool may contact hidden
wiring or its own cord. Contact with a "live" wire
will also make exposed metal parts of the power
tool "live" and could give the operator an electric
shock.
f. When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut
and reduces the chance of blade binding.
g. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
If both