In The Case Of Technical Problems; Repair Service; Information For Environmental Protection/ Disposal; Spare Parts - IKRA AKS 4030 Manuel D'utilisation

tilation slits for cooling the motor in the housing of the
chain saw is free (danger of overheating).
• If the saw chain is particularly dirty, e.g. in case of
gumming with resin, remove the chain and clean it.
Place the chain for a few hours in a vessel containing
chainsaw cleaner. There-after clean the chain with
clear water. If the chain is not used again immediately,
it must be treated with service spray or a customary
anticorrosion-spray.
• Only in case of use of biological oil: As some biological
oils may tend to encrust after a time, the oiling system
should be rinsed thoroughly before storing the chain
saw for a longer period. Therefore, please fill half of
the oil reservoir (about 100 ml) with chainsaw cleaner
and close it as usual. Then switch on the chainsaw
- without bar and chain being mounted - and keep it
running until the total rinsing liquid has evaporated
through the oil opening of the chain saw. Before using
the chain saw again, it is absolutely necessary to refill
the oil reservoir.
• Do not store the saw outdoors or in damp and moist
areas.
• Check all the chain saw parts, in particular the chain,
bar and sprocket, of wear after every use.
• Ensure that the chain tension is correct. If the chain
is too loose, it may come off during use and lead to
injuries. The chain must be replaced immediately if it is
damaged. The cutting teeth must be at least 4 mm long.
• Check the motor housing and rechargeable battery
after every use for damage. If there is any sign of
damage, have the chain saw checked by a specialised
workshop or the works after-sales service.
• Check the oil level and lubrication of your chain saw
after every use. Insufficient lubrication leads to dam-
age to the chain, bar and motor.
• Check how sharp the chain is every time before you
use the chain saw. A blunt chain will cause overheating
of the motor.
• Sharpening a saw chain requires experience and spe-
cialised knowledge. We therefore recommend to have
sharpening carried out by a specialised workshop.
• Before transporting the chainsaw, always remove the
battery and slide the chain guard over the rail and
chain. If several cuts are to be performed with the
chain saw, the saw must be switched off between cuts.
• When using a vehicle to transport the machine, posi-
tion it so that it can cause no danger to persons and
fasten it firmly.
• There are no parts to be maintained inside the de-
vice; the following therefore applies:
- Do not carry out any maintenance tasks that are not
described in these instructions. We cannot accept
any liability for accidents and damage caused by un-
authorised repair attempts, incorrect use or misuse.

In the case of technical problems

• Power does not turn on: Battery empty. Use spare
battery or charge the battery.
• Chain does not run:
Check position of handguard (see fig. 9). Chain only
runs if handguard brake is released.
GB | Operating Instructions
• Sparks fly at the motor:
• Oil does not flow:

Repair Service

Repairs to electric power tools should only be carried out
by specialist electrical personnel.
Always keep the original packaging for a possibly re-
quired shipping of the tool.
Information for environmental protection/ dis-
posal
Dispose of the machine properly after it is worn out. Dis-
connect the mains cable in order to prevent misuse. Do
not dispose of the machine with the household waste. In
the interest of environmental protection, take it to a col-
lection point for electric machines. Your responsible local
authority can provide you with addresses and operating
times. Also take the packaging materials and worn out
accessories to the appropriate collection points.
In accordance with European Directive 2012/19/EC on
waste electrical and electronic equipment and its im-
plementation in national law, waste electric tools must
be collected separately for environmentally-compatible
re-use.
Recycling alternative to the return invitation:
Instead of returning the electric equipment, the owner is
alternatively obligated to take part in the proper recycling
in the case of relinquishment of ownership. The waste
equipment can also be taken to a collection facility which
disposes of it in the sense of the national recycling man-
agement and waste acts. This does not pertain to the ac-
cessory parts and auxiliary equipment without electrical
components accompanying the waste equipment.

Spare parts

Please contact our service department if you need acces-
sories or spare parts.
When working with this machine, do not use spare parts
other than those recommended by us. Using spare parts
not recommend by us can result in serious injuries to per-
sons or damage to the machine.
The following information should be provided when or-
dering spare parts:
11
Motor or carbon brushes damaged. Take the chain
saw to a specialised work-shop or the works af-
ter-sales service.
Check the oil level. Clean the oil flow openings in the
bar. If this is not successful, take the chain saw to a
specialised work-shop or the works after-sales service.
Attention: Any maintenance or repair work go-
ing beyond that described in these Operating
Instructions may only be carried out by author-
ised persons or the works after-sales service.
Only for EU countries
Do not discard electric tools in the household
waste!