Using Hdmi Input; Connecting Hdmi Equipment - Pioneer PureVision PDP-506XDE Mode D'emploi

Enjoying through External Equipment

Using HDMI Input

This Plasma Display System is equipped with two HDMI
terminals (INPUT 3 and 4) which accept digital video and audio
signals. To use the HDMI terminal, activate the terminal and
specify the types of video and audio signals to be received from
the connected equipment. For the types of these signals, see
the operation manual that came with the connected
equipment.
Before starting the menu, press INPUT 3 or INPUT 4 on the
remote control unit or press INPUT on the Media Receiver to
select INPUT 3 or INPUT 4.
Input signal correlation table
1920*1080i@50Hz
720*576p@50Hz
1280*720p@50Hz
720(1440)*576i@50Hz
1920*1080i@59.94/60Hz
720*480p@59.94/60Hz
1280*720p@59.94/60Hz
720(1440)*480i@59.94/60Hz
1920*1080p@24Hz
For audio, the system supports the following:
• Linear PCM (STEREO 2ch)
• Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz
NOTE
• PC signals are out of correspondence.

Connecting HDMI equipment

When using the INPUT 3 HDMI terminal:
Media Receiver (rear view)
I N O U T
SERVICE ONLY
CONTROL OUT IN
ANT(DIGITAL)
INPUT 1
ANT i /o link.A
SELECT
INPUT
2 3
INPUT 1
HDMI cable
(commercially
available.)
SCART cable
(commercially available.)
Connect the SCART cable only
when inputting analogue audio
signals.
HDMI equipment
OPTICAL
DIGITAL OUT COMMON INTERFACE
INPUT 2
R-AUDIO-L SUB
Y P B P R
WOOFER
COMPONENT VIDEO AUDIO OUTPUT
INPUT 3
BLACK
HDMI HDMI WHITE
INPUT 4
SYSTEM CABLE
When using the INPUT 4 HDMI terminal:
Media Receiver (rear view)
I N O UT
SERVICE ONLY
CONTROL OUT IN
ANT(DIGITAL)
INPUT 1
ANT i /o link.A
SELECT
INPUT
2 3
INPUT 1
HDMI cable
(commercially
available.)
HDMI equipment
To activate the HDMI terminal:
When you use the INPUT 3 HDMI terminal, use the following
procedure to activate the terminal.
1
Press HOME MENU.
2
then ENTER).
Select "Option" ( /
3
Select "HDMI Input" ( /
4
then ENTER).
Select "Setting" ( /
5
then ENTER).
Select "Enable" ( /
Item Description
Disable Deactivates the HDMI terminal.
(factory default)
Enable Activates the HDMI terminal.
6
Press HOME MENU to exit the menu.
NOTE
• You need not activate the INPUT 4 HDMI terminal; you
cannot manually deactivate this terminal.
To specify the type of digital video signals:
1
Repeat steps 1 to 3 provided for "To activate the HDMI
terminal."
2
then ENTER).
Select "Video" ( /
3
Select the type of digital video signals ( /
• If you select "Auto", an attempt will be made to identify
the type of digital video signals when digital video
signals are received.
Item Description
Auto Automatically identifies input digital video signals.
(factory default)
Colour-1 Digital Component Video signals (4:2:2) locked
Colour-2 Digital Component Video signals (4:4:4) locked
Colour-3 Digital RGB signals locked
4
Press HOME MENU to exit the menu.
OPTICAL
DIGITAL OUT COMMON INTERFACE
INPUT 2
Y P P R-AUDIO-L SUB
B R
WOOFER
COMPONENT VIDEO
AUDIO OUTPUT
INPUT 3
HDMI HDMI BLACK WHITE
INPUT 4
SYSTEM CABLE
then ENTER).
then ENTER).
13
61
En