Bar And Chain Combinations; Spare Parts And Accessories - Stihl GTA 26 Notice D'emploi

20 Bar and Chain Combinations

– Cord length 10 m up to 30 m: AWG 12 /
3.5 mm²
19.7 Temperature limits
WARNING
■ The battery is not protected against all ambi‐
ent conditions. If the battery is exposed to cer‐
tain ambient conditions, it may catch fire or
explode. There is a risk of serious injury to
people and damage to property.
► Do not charge the battery below -20°C or
above +50°C.
► Do not use the garden pruner, battery or
charger below -20 °C or above +50 °C.
► Do not store the garden pruner, battery or
charger below -20 °C or above +70 °C.
19.8 Recommended temperature
ranges
For optimum performance of the garden pruner,
batteries and charger, observe the following tem‐
perature ranges:
– Charging: 5°C to 40°C
– Use: - 10 °C to + 40 °C
– Storage: - 20 °C to + 50 °C
If the battery is charged, used or stored outside
the recommended temperature ranges, perform‐
ance may be reduced.
19.9 Sound Values and Vibration
Values
K-value (uncertainty) for sound pressure levels is
2 dB(A). K-value (uncertainty) for sound power
20 Bar and Chain Combinations
20.1 STIHL GTA 26 Garden Pruner
Pitch Drive link
gauge/groove
width
1/4" P 1.1 mm
The cutting length of a guide bar depends on the garden pruner model being used and the saw chain.
Actual cutting length may be less than the specified length
21 Spare Parts and Accesso‐
ries
21.1

Spare parts and accessories

These symbols indicate original STIHL
spare parts and original STIHL acces‐
sories.
0458-694-9621-B
Length Guide bar
10 cm Light
levels is 2 dB(A). K-value for vibration level is
2 m/s².
STIHL recommends wearing ear defenders.
– Sound pressure level L
to EN 60745‑2‑13: 77 dB(A)
– Sound power level L
EN 60745-2-13: 86 dB(A)
– Vibration level a measured according to
hv
EN 60745-2-13:
– Control handle: 2.8 m/s²
– Grip surface: 2.9 m/s.
The vibration levels indicated were measured
according to a standardized test method and can
be used as a basis for comparing electric power
tools. The vibration levels actually occurring may
vary from the values indicated, depending on the
type of application. The vibration levels indicated
can be used for an initial estimate of the vibration
stress. The actual vibration stress has to be esti‐
mated. The times when the power tool is
switched off and the times when it is switched on
but running under no load can be taken into
account in the estimate.
For information on compliance with Employers'
Vibration Directive 2002/44/EC see
www.stihl.com/vib.
19.10 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation see www.stihl.com/reach.
Nose spro‐ Number of
cket teeth drive links
–
STIHL recommends the use of original STIHL
spare parts and accessories.
Despite ongoing market observation, STIHL is
unable to judge the reliability, safety and suitabil‐
ity of other manufacturers' spare parts and
accessories; accordingly, STIHL cannot warrant
for the use of those parts.
English
measured according
pA
measured according to
wA
Saw chain
71 PM3 (Type
28
3670)
47