ABS TriPole Mode D'emploi page 6

6
This notice must be translated (possibly by the retailer) into
the language of the country of use. For your safety, comply
strictly with the instructions for use, verification, maintenance
and storage.
ABS SAFETY GMBH cannot be held liable for any direct or in-
direct accident occurring as a result of use other than provi-
ded for in this notice; do not use this equipment beyond its
capabilities!
USE AND PRECAUTIONS
The TRIPOD is a temporary and transportable anchorage point,
it is expected to be used to provide an access to confined
spaces : tanks, silos, sewers, wells, ...
It complies with the standard EN795 class B and with the Ma-
chinery directive 98/37CEE to lift a weight of 200 kg maximum.
Two versions are existing (see marking page). All the elements
(detent pin ball, strap support, anchor plate, axis of pin,...) can-
not be lost.
Il tripod has 3 anchorages:
Anchorage point 1 : two anchoring rings in aluminium located
under the tripod head which allows to set a fall arrest system
EN363 (retractable fall arrester, sliding fall arrester on flexible
anchor line,...) or suspension work devices on ropes.
Anchorage point 2 : constituted of a plate with a support handle
already set on an aluminium tube for installation of a rescue
device by raising EN1496 Class A (« type » winch (see Fig 1)
please see the instructions for use of the winch to install it on
the Tripod) or class B.
In all cases, to connect the anchor point with the system at-
tached on it, a connector will have to be used (EN362)
The TRIPOD is a piece of personal protection equipment; it
should be allocated to a single user (it can only be used by one
person at a time).
But the presence of a third party is necessary during rescue
operations by raising.
User safety relies on the effectiveness of the equipment and
full understanding of the safety instructions contained in this
leaflet.
Product markings should be checked periodically for legibility.
The TRIPOD has to be located above the user (minimum resis-
tance of 10 kN). Check that the general disposition limits the
pendulum movement in case of fall and that the work is done in
order to limit the risk and the fall height. It is essential to check
the free space under user's feet depending on the device used.
Before and during use, we recommend that you take all the
necessary precautions for a safe rescue should it be needed.
This equipment is for the sole use of people trained, skilled and
in good health, or under the supervision of a trained and skilled
person. Warning! Certain medical conditions may affect user
safety; if in doubt, consult your doctor.
Before each use, please check : the rotation of the feet around
the axes, the articulations on TRIPOD's head, the rubber pads
under the feet (They provide stability and ensure adherence
with the ground), the state the strap is, the tubes (no deforma-
tion), the detent pin ball, axis of pin, the plate (no deformation
or corrosion marks)...
ABS TriPole
Do not remove, add or replace any component of the product.
Chemical products: put the system out of use if it comes into
contact with chemical products, solvents or fuels which could
affect its workings.
TECHNICAL DATA:
Tubes and TRIPOD's head : Aluminium / Axis of pin and plate :
Steel / Strap : Polyester
ABS Safety GmbH certifies that the TRIPOD has been tested in
accordance with the standard EN 795 class B
SUITABILITY FOR USE:
A fall arresting harness (EN361) is the only body gripping device
that may be used. It may be dangerous to create one's own
fall arrester system where each safety function can interfere
with another safety function. Therefore, it is important to read
the recommendations on using each component in the system
before use
VERIFICATION:
The recommended service life of the equipment is 10 years,
but it may be increased or reduced according to the use and/
or the results of the annual inspections. The equipment should
be inspected if there is any doubt, or following a fall and at
least annually, by the manufacturer or a competent person au-
thorised by the manufacturer to check its strength and hence
the user's safety.
The product data sheet should be completed after each annual
product verification.
SERVICING AND STORAGE
(Comply strictly with these instructions)
During transport, keep the product in its packaging, well away
from any cutting surface; clean it with water, wipe it with a rag
and hang it up in a well-ventilated location, to let it dry naturally
and away from a naked flame or heat source; follow the same
procedure for components that have become damp during use.
The system must be stored in its packaging in a dry, well aired
place protected from extremes of temperature.
EN