Mitsubishi Electric LGH-F300RVX2-E Notice D'installation page 21

5. Function settings (continued)
No.43
Indoor temperature correction
Set the correction for the indoor temperature displayed on the
PZ-62DR-E screen by function
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
- -
- -
- -
N/A - - 43
- -
- -
- -
- -
- -
- -
- -
No.44
CO concentration correction
2
CO concentration displayed on the PZ-62DR-E can be corrected.
2
This function is available when there is CO
the location of CO sensor.
2
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
- -
- -
- -
N/A - - 44
- -
- -
- -
- -
- -
No.45
Supply fan monitor threshold
The threshold fan speed of supply fan monitor output can be
selected.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW PZ-62DR-E
Setting
check
SW No. Setting Function No. Setting Data
- -
- -
N/A 45
- -
- -
.
No. 37
Setting The correction to
check thermistor detection
0 -7 K (-12.6 °F/-7 °C )
1 -6 K (-10.8 °F/-6 °C )
2 -5 K (-9 °F/-5 °C )
3 -4 K (-7.2 °F/-4 °C )
4 -3 K (-5.4 °F/-3 °C )
5 -2 K (-3.6 °F/-2 °C )
6 -1 K (-1.8 °F/-1 °C )
7
0 K (0 °F/0 °C )
(Factory setting)
8 +1 K (+1.8 °F/+1 °C )
9 +2 K (+3.6 °F/+2 °C )
10 +3 K (+5.4 °F/+3 °C )
11 +4 K (+7.2 °F/+4 °C )
12 +5 K (+9 °F/+5 °C )
13 +6 K (+10.8 °F/+6 °C )
14 +7 K (+12.6 °F/+7 °C )
concentration gap due to
2
Setting CO concentration
2
check correction
0 -500 ppm
1 -400 ppm
2 -300 ppm
3 -200 ppm
4 -100 ppm
5
±0 ppm
(Factory setting)
6 100 ppm
7 200 ppm
8 300 ppm
9 400 ppm
10 500 ppm
Setting Supply fan monitor
check threshold
0
Fan speed 1 or higher
(Factory setting)
1 Fan speed 2 or higher
2 Fan speed 3 or higher
3 Fan speed 4
No.46
Exhaust fan monitor threshold
The threshold fan speed of exhaust fan monitor output can be
selected.
This function is N/A from Lossnay unit DIP-SW.
DIP-SW
Setting
check
SW No. Setting
- -
- -
N/A
- -
- -
Automatic ventilation mode setting 1)
No.52
Outdoor and indoor temperature gap
Set one of conditions for By-pass mode in auto ventilation operation,
temperature gap between indoor and outdoor.
This function is N/A from Lossnay unit DIP-SW.
This function can also be set on the Auto By-pass settings screen of
the PZ-62DR-E.
DIP-SW
Setting
check
SW No. Setting
- -
- -
- -
- -
N/A
- -
- -
- -
- -
Automatic ventilation mode setting 2)
No.53
The lowest outdoor temperature
Set one of conditions for By-pass mode in auto ventilation operation,
minimum outdoor temperature which comes in indoor directly.
This function is N/A from Lossnay unit DIP-SW.
This function can also be set on the Auto By-pass settings screen of
the PZ-62DR-E.
DIP-SW
Setting
check
SW No. Setting
- -
- -
- -
- -
- -
- -
- -
- -
N/A
- -
- -
- -
- -
- -
- -
- -
- -
Eng-21
PZ-62DR-E
Setting Exhaust fan monitor
check threshold
Function No. Setting Data
0
Fan speed 1 or higher
(Factory setting)
1 Fan speed 2 or higher
46
2 Fan speed 3 or higher
3 Fan speed 4
PZ-62DR-E
Setting Gap between Indoor
check temp. and Outdoor temp.
Function No. Setting Data
0
0 K (0 °F/0 °C ) or more
(Factory setting)
1 1 K (1.8 °F/1 °C ) or more
2 2 K (3.6 °F/2 °C ) or more
3 3 K (5.4 °F/3 °C ) or more
52
4 4 K (7.2 °F/4 °C ) or more
5 5 K (9 °F/5 °C ) or more
6 6 K (10.8 °F/6 °C ) or more
7 7 K (12.6 °F/7 °C ) or more
PZ-62DR-E
Setting
Outdoor temperature
check
Function No. Setting Data
0 50 ˚F (10 ˚C) or more
1 52 ˚F (11 ˚C) or more
2 54 ˚F (12 ˚C) or more
3 55 ˚F (13 ˚C) or more
4 57 ˚F (14 ˚C) or more
5 59 ˚F (15 ˚C) or more
6
61 ˚F (16 ˚C) or more
(Factory setting)
7 63 ˚F (17 ˚C) or more
53
8 64 ˚F (18 ˚C) or more
9 66 ˚F (19 ˚C) or more
10 68 ˚F (20 ˚C) or more
11 70 ˚F (21 ˚C) or more
12 72 ˚F (22 ˚C) or more
13 73 ˚F (23 ˚C) or more
14 75 ˚F (24 ˚C) or more
15 77 ˚F (25 ˚C) or more