Silverline 261310 Mode D'emploi page 5

261310
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool's
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
Additional Safety for SDS Drills
• Do not allow anyone under the age of 18 years to use this tool, and ensure that
operators are qualified and familiar with the operating and safety instructions
• Masonry drilling or chiselling can create sharp particles that will impact the operator.
Wear impact-resistant safety glasses and protective clothing, including safety boots
• Core drills should only be used with SDS drills featuring a safety clutch to prevent
jamming, which could cause an injury to the operator
• Do not operate SDS drills whilst up a ladder or in any location where there is a risk of
falling. SDS drills are heavy and produce strong vibration and high torque in use
• Wear suitable protective anti-vibration gloves that are non-fabric or coated fabric
to prevent loose strands of material catching in the rotating drill bit. Discard gloves
immediately if material is visibly frayed
• Drilling can produce large volumes of dust and debris that may be toxic. Wear
respiratory protection suitable for the work being undertaken. A minimum rating of
FFP2 is recommended
• SDS drills produce high volumes of noise and suitable ear protection must be worn at all
times while operating the tool
• SDS drills produce a very high level of vibration when operating in hammer or chisel
mode. Frequent breaks are advised
• Use metal and voltage detectors to locate concealed electric, water or gas lines. Avoid
touching live components or conductors
• Extension cable reels used with this tool must be completely unwound. Minimum
conductor cross section: 1.25mm2
• Extension reels used outside should be designed for outdoor use and should feature
water-protected sockets and correct cable insulation
• When using an SDS drill outdoors, an RCD device must be used either by connecting to
a socket which incorporates an RCD, or through use of an inline RCD
• Ensure that the chisel or drill bit is securely fixed in the chuck before operating the tool.
Insecure drill bits can be ejected from the machine, causing a hazard
• Ensure lighting is adequate
• Drill bits become hot during operation. Allow to cool prior to handling
• If you are interrupted when operating the drill, complete the process and switch off
before diverting your attention elsewhere
• Always disconnect the SDS drill from the electric supply before changing a chisel or
drill bit
• Examine the chuck regularly for signs of wear or damage. Have damaged parts repaired
by a qualified service centre
• Always wait until the drill has come to a complete stop before placing it down
• On completion of the work, disconnect the tool from the power source and remove the
chisel/bit from the machine
• Periodically check all nuts, bolts and other fixings and tighten where necessary
• Visibly check the tool after use, especially the power cable, which can be damaged by
sharp masonry
• Always fit the dust guard to the bit in use to prevent damage from debris entering the
SDS chuck
• If operating the tool causes discomfort in any way, stop immediately and review your
method of use
1500W SDS Plus Hammer Drill
Product Familiarisation
1 SDS Plus Chuck
2 Chuck Protective Cover
3 Rotation Selection Switch
4 Gearbox Cover
5 On/Off Trigger Switch
6 Hammer Selection Switch
7 Variable Speed Control
8 Brush Access Cover
9 Chisels (x 2)
10 Dust Guard
11 Depth Gauge
12 Masonry SDS Drill Bits (8, 10 & 12mm)
13 Gearbox Pin Spanner
14 Pot of Grease
15 Auxiliary Handle
16 Depth Gauge Mounting
17 Keyed Chuck
18 SDS Plus Arbor
19 Chuck Key
Additional Supplied Accessories (not shown)
• Blow moulded case
Note: The Keyed Chuck (17), SDS Plus Arbor (18) and Chuck Key (19) are not included with
all versions of this SDS drill. These items are available as Silverline 13mm Chuck & SDS
Plus Adaptor Kit product code 292703.
Unpacking Your Tool
Carefully unpack and inspect your tool. Familiarise yourself with all its features and
functions.
Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool.
www.silverlinetools.com
5