Efire Controller Application; Low Battery; Battery Holder / Backup Installation - Napoleon GX70NTE-1 Manuel D'installation Et D'opération

"beep" will confi rm the reception of the command.
operation
EN
8.9

eFIRE Controller application

child lock
Napoleon's eFIRE application will revolutionize the way you use your fireplace! We have cracked the code and
present to you the first fireplace to be controlled by Bluetooth technology, using an intuitive app on your mobile
ADD TITLE: Night Light Dimmer Control
device.
The auxiliary function controls the Night Light™ with dimmable control.
A. Use the mode key to guide you to the Night Light™ icon.
When fully equipped (if applicable), the eFIRE application allows you to select from a multitude of colours to suit
your mood or décor simply by scrolling through the colour wheel. Additionally, Napoleon's eFIRE application allows
B. The intensity of the output can be adjusted through 6 levels.
you to control many other functions of your fireplace, including on/off, flame height, light feature, blower, and a
Use the up/down arrow keys to adjust the output level. A single beep
timer to create a schedule for your fireplace that works for you. will confi rm reception of the command.
ADD TITLE: CONTINUOUS PILOT / INTERMITTENT PILOT (CPI / IPI) SELECTION
Using the instructions on the eFIRE Controller application website http://napoleonfireplace.com/efire, install
A. When the transmitter is in the off position, use the mode key to guide
the application and enjoy the features the eFIRE Controller application has to offer. *
you to the CPI mode icon.
B. Press the up/down to switch between IPI and CPI modes. A single
* Visit the website or contact your authorized dealer for appliance-specific information and/or frequently asked
beep will confi rm reception of the command.
questions regarding features and products available with the eFIRE Controller application.
note:
If the appliance is equipped with a CPI/IPI toggle switch, set the CPI/IPI
note:
to CPI position to enable remote CPI operation. If the switch is set to IPI
The remote control is considered the master control for the appliance and can always be used to turn the
then it will only work in IPI regardless of what is set on the remote control
appliance off (ex. the eFIRE Controller application user, in control of the appliance, leaves the home).
handset.
ADD TITLE: LOW BATTERY / MANUAL BYPASS

8.10 low battery

The life span of the remote batteries depends on various factors: quality of the batteries,
the number of ignitions, etc.
When the transmitter batteries are low, a battery icon will appear on the LCD display
before all battery power is lost. When the batteries are replaced, this icon will disappear.
When the receiver batteries are low, no "beep" will be emitted from the receiver when
it receives an on/off command. This in an alert for the receiver that there's low battery.
When the batteries are replaced the "beep" will be emitted from the receiver when the on/off key is pressed.
If the batteries of the receiver or transmitter are low, the appliance can be turned on manually by sliding the
three position slider switch on the receiver to the on position. This will bypass the remote control feature and the
appliance main burner will come on if the gas valve is in the on position.
ADD TITLE: IN THE EVENT OF A POWER FAILURE

8.11 battery holder / backup installation

If the receiver is equipped with batteries they will enable fl ame height control or on/off function to control the
A. The battery holder is located in the valve compartment,
appliance during a power failure. Blower and Night Light™ operation is not possible. Refer to "appliance
accessible for programming the remote.
operation" section when communications between receiver and transmitter have been lost. The receiver will
emit a "beep" sound to confi rm programming has been successful once power is restored. During a power
B. Install 4 AA batteries, Ensure that the positive and negative
failure, if the appliance was on, the fl ame height will stay at the setting prior to the failure. If off when the failure
occurs and then turned on, the fl ame height will come on at "Hi". The fl ame height can then be controlled by the
ends correspond with those identified in the battery holder.
remote.
C. In the case of a power outage, the 3 position slider switch
needs to be in the "ON" position (left).
note:
Ensure the 3 positions slider switch is in the "REMOTE"
position (middle).
30
W415-1793 / B / 08.23.18
Set Temperature
Flame Off
SMART
76
73
ON
MAX
Set Temperature
76
Room Temperature
OFF
SMART
68
ON
Flame Off
MAX
Set Temperature
76
child lock
OFF
SMART
Flame Off
MAX
76
child lock
OFF
73
73
Flame Off
child lock
Room Temperature
Room Temperature
68
ON
68
ON
Set Temperature
Set Temperature
SMART
SMART
MAX
76
MAX
76
OFF
OFF
Flame Off
Flame Off
child lock
child lock
Mode Key
76
Flame at level 1 Flame at level 5
°F
Room Temperature
76
23
°F
°F °C
°F
68
76
°F °F
76
°F
76
°F
Flame at level 1
76
°F
76
76
°F °F
Blue LCD Display
°F
On / Off Key
Blue LCD Display
Temperature Key
On / Off Key
Up / Down Arrow Key
Temperature Key
Flame at level 1
Up / Down Arrow Key
Mode Key
76
76
°F
Mode Key
°F °F
23
°F °C
23
°F °C
Flame at level 1
76
°F
76
°F
76
°F
76
°F
76
°F
RESET/PROGRAM BUTTON (PRG)
76
°F °F
76
°F °F
Flame at level 1
76
Flame at level 1
°F
76
°F
76 76
76 76
OFF
°F
76
68 Hi
Flame at "Hi" level 6
°F
76 76
°F
IPI CPI
76 76
76 76
°F
°F
76 76
OFF
68 Hi
°F
Hi
Flame at level 5 Flame at "Hi" level 6
76 76
76 76
°F
°F
76
OFF
IPI CPI
°F
76
76
OFF
°F 76
Hi
°F
OFF
Flame at level 5 Flame at "Hi" level 6
76 76
76
°F
76
76
IPI CPI
°F
76
Hi
Flame at level 5 Flame at "Hi" level 6
76 76
76
°F
°F
IPI CPI
68
76
°F
68
76
°F
OFF
76
°F
OFF
76
°F
76
°F
Flame at level 5 Flame at "Hi" level 6
76
23.3
Flame at level 5 °F Flame at "Hi" level 6
IPI CPI
76
°F
°F
°F
°F
°F
°F
°F
°F
76
°F
ON
°F 76
°F
ON
°F
°F
°F
°F
76
°F
°F
Hi
76
°F
Hi
76
°F
76
°F
76
°F
76
Hi
°F
Hi
76
°F
76
°F