Publicité
Les langues disponibles
Les langues disponibles
CONTROLS AND CONNECTIONS
DUAL MULTIEFFECT DSP
With 56-bit internal DSP and 24-bit Delta-Sigma conversion, the
two internal effects (160 programs each) provide high performance
digital audio processing combined with extremely easy operation.
19
Program LED display: shows the number of the currently
selected program.
20
PROGRAM: program selection keys allow to select any
memory number to call one of the 160 programs available.
= decrement key
= increment key
21
INPUT LEVEL: 5-segment input level LED indicator.
A good setting of the effect sends (1 and 2) on each channel will
produce continuous lighting of the green LED segments, while the
red segment must flash only occasionally.
If the red LED is continuously lighted it indicates signal overload
and it is necessary to reduce the effect send volumes (1 and 2)
on individual channels.
22
TONE control: Turning this control clockwise produces a
gradual decrease in high frequencies. Fully anticlockwise the
response is flat.
23
A / B: monitor sends. Allow to adjust the level of the stereo
effect in the monitor mixed outputs 'A' and 'B'.
24
ON: effect on/off button, with green LED indicator.
25
BAL: balance. Allows to adjust the level of the stereo signal
in the L and R master outputs.
26
VOLUME fader.
connections:
27
EFF 1 - EFF 2 / MUTE: jack sockets for connection of remote
footswitches. They allow remote control enabling/disabling of the
built-in effect processors. This is possible only when the "ON"
buttons are pushed.
The 'Mute' LED indicator lights when the effect is off.
EXTERNAL EFFECTS SENDS AND RETURNS
28
1 / 2 external effects sends: level controls for the external
effects sends. They are the mixes of the signals sent from '1' and
'2' sends volumes on each channel and set the level of the signal
appearing at the 'EFF SEND 1' and 'EFF SEND 2' jack outputs.
Each one of the two STEREO RETURNS features
29
GAIN: adjusts the gain (sensitivity) of the effect return.
30
A / B: monitor sends controls. Set the level of the external
effect to be sent to the A and B monitor outputs.
31
BAL: stereo balance of the external effect. Allows to adjust
the level of the stereo signal of the effect in the L and R master
outputs.
32
PEAK: peak LED indicator.
33
VOLUME fader.
connections:
34
EFF SEND 1/2: jack output sockets for the external effects
sends.
35
STEREO EFF RET 1/2: jack inputs for the external effects
returns.
Connect the inputs of the external effects to the EFF SEND 1/2
output sockets.
Connect the L and R outputs of the stereo external effects to the
L and R 'EFF RET 1' and 'EFF RET 2' inputs.
• For a mono effect connect its 'only effect' output to the 'R / mono' socket.
Use the controls 1 and 2 on each channel to determine the
quantity of channel's signal to be sent to the external effects, the
EXTERNAL EFFECTS SEND 1 and 2 controls (28) to determine the
quantity of signal to be sent to the EFF SEND 1 and 2 outputs, and
the GAIN, A, B and BAL (29, 30, 31) controls, of the 'stereo effects
returns' section, to adjust the effect return level in the 'A' and 'B'
monitor outputs and in the 'L' and 'R' master outputs.
In the channels where one or both external effects are not desired,
turn the correspondent control fully anticlockwise.
Note: The stereo inputs EFF RET 1 and 2 are normal stereo line inputs. You can
thus use them to connect any line signal (such as the L/R outputs of a second
mixer, instruments, expanders...).
see fig. 4 page 22
7
Publicité
