Technical Data; Installation - Scheppach ASP30-ES Traduction Des Instructions D'origine

6. Technical Data

Mains voltage
Power
Maximum device socket
power
Total power
Water tank capacity
Suction performance
Protection category
Protection class

7. Installation

m IMPORTANT!
Prior to use, ensure that the device has been cor-
rectly and fully assembled.
Unpacking (Fig. 1, 2, 3)
• Release the locking hooks (4) and remove the ma-
chine head (2). The accessories are located inside
the stainless steel container (9). Only the metal ex-
tension tube (22) is located outside the stainless
steel container (9) in the packaging. Remove all of
the accessories from the stainless steel container
(9).
Installing the castor mounts (5) (Fig. 4, 5)
• Turn the stainless steel container (9) upside-down
(the machine head (2) must be removed).
• Push the castor mounts (5) into the cut-outs pro-
vided on the wheel mounting base (7). (4x)
• Fasten the castor mounts (5) with a screwdriver
(not included in the delivery) and one screw each
(23). (4x)
Installing the castors (6) (Fig. 6)
• Press the four castors (6) into the holes in the wheel
mounting base (5).
Installing the machine head (2) and the handle (1)
(Fig. 7)
• Place the machine head (2) on the stainless steel
container (9). Secure the machine head (2) with
the locking hooks (4). When installing the machine
head (2), ensure that the locking hooks (4) latch into
place correctly.
• Place the handle (1) on the machine head (2) and
fasten it with two screws (23) with a screwdriver
(not included in the delivery).
18 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
220-240 V~ 50/60 Hz
1400 W
2000 W
3400 W
30 L
20 Kpa
IPX4
I
Installing the foam filter (17) (Fig. 3, 8)
Never use the device without filter! Always ensure
that the filters are correctly fitted!
• Installing the foam filter (17): For wet vacuuming,
slide the foam filter (17) provided over the filter bas-
ket with safety float valve (15).
Installing the folded filter (19) (Fig. 3, 9)
For dry vacuuming, slide the folded filter (19) provided
over the filter basket with safety float valve (15). The
folded filter (19) is only suitable for dry vacuuming!
Installing the paper filter bag (18) (Fig. 3, 10)
It is recommended to use an additional paper filter
bag (18) when vacuuming fine, dry dirt.
• Slide the paper filter bag (18) over the suction open-
ing in the stainless steel container (9). The paper fil-
ter bag (18) is only suitable for dry vacuuming. The
paper filter bag (18) makes it easier to dispose of
the dust collected.
Installing the suction hose (16) (Fig. 3, 11, 12)
Connect the suction hose (16) to the corresponding
port, depending on the desired use, on the wet and
dry vacuum.
Vacuuming:
Connect the suction hose (16) to the suction hose port
(10). To do so, slide the end of the suction hose (16)
with the two nipples into the suction hose port (10)
(A). Insert the two nipples into the recesses. Once
the suction hose is fully inserted, turn it clockwise (B).
Blowing:
Connect the suction hose (16) to the blowing func-
tion connection port (14). Slide the end of the suction
hose (15) with the two nipples into the blowing func-
tion connection port (14). Insert the two nipples into
the recesses. It is not necessary to turn it here.
Installing the metal extension tube (22), suction
hose (16) and nozzles (20/21) (Fig. 13)
• Connect the metal extension tube (22) with the bent
end of the suction hose (16).
• Fit the floor nozzle (20) or joint nozzle (21) to the
other end of the metal extension tube (22).
• Push the slide piece forwards (A) to change the
length of the metal extension tube (22). (Fig. 14)
• Pull the tube to the desired length (B). Ensure that
the slide lock latches into place. (Fig. 14)
Installing the bottom cable holder (Fig. 3, 15)
Clip the bottom cable holder (24) onto the wheel
mounting base (7) at the rear of the device. The top
cable holder (13) is on the connection port for the
blower function (14).