Weller SI 120 Mode D'emploi page 8

English
Technical Data
Mains supply
Rated input
Safety class
The following safety regulations must be observed to
protect the health of personnel and to prevent electric
shocks, injury and the risk of fire and explosions. Failure to
observe the safety regulations results in a risk to life and
limb.
These Operating Instructions and safety information must
be kept well visible in the vicinity of the soldering tool.
Specified Conditions Of Use
Use the soldering iron exclusively for the purpose
indicated in the Operating Instructions of soldering and
desoldering under the conditions specified here.
The manufacturer shall not be liable for damage resulting
from misuse of the machine or unauthorised alterations.
Safety information
This appliance can be used by
children aged from 8 years and
above and persons with reduced
physical, sensory or mental capabili-
ties or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way
and understand the hazards involved.
Children shall not play with the
appliance. .
WARNING!
Fire and explosion hazard!
Risk of burns
„Do not touch the hot soldering tips and keep them away
from inflammable objects.
„Due to the high temperatures, it is recommended that
the workpiece be fixtured.
„After the soldering process, the soldering tool and the
workpiece holder are still hot.
„Risk of burning through liquid solder.
„Keep explosive and flammable objects well away from
the device.
„Caution! Covering the soldering iron or the safety holder
poses a fire hazard. Always keep objects well away from
the soldering iron and safety holder.
Wear appropriate protective clothing to protect yourself
against burns. Protect your eyes by wearing eye
protectors.
Always place the soldering tool in the safety holder
provided. Make sure the safety holder is stable.
Be alert. Do not use the soldering tool if you are having
difficulty concentrating.
Protect yourself against electric shocks. Avoid touching
earthed objects such as pipes, heaters, cookers and
refrigerators.
Take account of environmental influences. Do not use the
soldering tool in a damp or wet environment.
Never work on voltage-carrying parts.
Valid safety provisions and accident-prevention
regulations must be observed.
8
SI 120
230 V ~ 50 Hz 230 V ~ 50 Hz
120 W
I
Avoid abnormal posture. Arrange your work station in an
ergonomically correct way.
Before use check machine, cable, and plug for any
damages or material fatigue. The soldering tool must be
operated only in perfect technical working order.
Do not overload your soldering tool.
The mains cable must only be plugged into the mains
socket or adapter approved for this purpose. Check that
the mains voltage is compatible with the connected load of
the soldering iron.
Do not use the cable for purposes other than those for
which it is intended. Do not use the cable to pull the plug
out of the socket. Protect the cable against heat, oil and
sharp edges.
Avoid unintentional operation. Disconnect the soldering
tool from the power supply while not in use.
Store your soldering tool in a safe place.
Maintenance and repair
Before doing any work on the machine, pull the plug out of
the socket.
Follow the instructions on soldering tip replacement.
Use original replacement parts only.
Always have your soldering tool repaired by a qualified
electrician.
If the power cord of the power tool is damaged, it cannot
be replaced; the power tool must be disposed of.
The soldering tips are provided with an electro-plated
protective layer. The protective layer considerably
lengthens the lifetime of the soldering tip and must never
be destroyed through mechanical adaptation (e.g. filing,
scratching).
For more information please visit www.apextoolgroup.eu.
Warranty
Weller supplies this device with a warranty valid for two (2)
years from the date of purchase. The warranty relates to
material and manufacturing defects and covers both
replacement parts and labour.
The warranty shall be void if damage is due to improper
use and if the device has been tampered with by
unauthorised persons.
This device conforms to the specifications of the EC
Declaration of Conformity with Directives 2004/108/EC,
2006/95/EC and 2011/65/EU (RoHS).
Subject to technical alterations and amendments.
Disposal
Do not dispose of electric tools together with
household waste material! In observance of
European Directive 2012/19/EU on waste
electrical and electronic equipment and its
implementation in accordance with national law, electric
tools that have reached the end of their life must be
collected separately and returned to an environmentally
compatible recycling facility.
SI 175 SI 251
230 V ~ 50 Hz
175 W 200 W
I I