TREND T12 Traduction Des Instructions Originales page 14

2. Unlock the plunge limiter by pushing the release lever
(6) down.
3. Lower the router carriage until the cutter is in contact
with the workpiece.
4. Press the quick locking button (7).
5. Set the quick height adjuster (16) to zero and reset
the fine adjust reset ring (19) to zero. The depth stop bar
(12) must be in contact with the turret stop (11).
6. Adjust the depth of cut using the quick height adjuster
(16) and the corresponding graduation. The adjusted
depth of cut is indicated by the pointer (17).
7.Tighten the quick height adjuster lock (15).
Fine Adjustment
When not using a depth template, or if the depth of cut
needs readjustment, it is recommended to use the fine
height adjuster (18).
1. Adjust the depth of cut as described in Adjusting the
Depth of Cut.
2. Set the fine height adjuster to zero using the fine zero
reset ring (19).
3. Rotate the fine height adjuster (18) to the required
position: one turn corresponds to approximately 1 mm
and 1 mark to 0.1 mm.
Fitting Template Guide Bush and
Inner Plate - (Fig. H)
The routers have a unique built-in line up system for the
template guide bush. This system ensures that the guide
bush is exactly concentric to the router cutter to ensure
accurate work.
1. Turn the router upside down.
2. Fit inner plate (58) into the recess in the router base
plate (10). For T12 the bushes on the inner plate must be
towards the router motor. For T14 the raised side of the
inner plate must be away from router base. Loosely fit
the two pan head machine screws (59) through the inner
plate and into the tapped holes. DO NOT TIGHTEN
SCREWS.
3. Fit the 30mm template guide bush (24) to the inner
plate (58). Fit guide bush with the two M5 countersink
machine screws (25). Tighten these screws.
4. The line-up pin (60) is stepped for 12mm and 1/2"
collet (9) sizes. (For the 1/2" collet simply push the line-
up pin further down into the 1/2" collet).
5. Fit line up pin (60) into the 1/2" collet (9) (or 12mm
depending on the size fitted) in the router, lightly tighten
collet nut to hold the line up pin (60).
6. Release plunge lever and gently depress base until
line up pin (60) projects through the 30mm guide bush
(24).
EN - T12/T14
7. Once in line, tighten the pan head machine screws
(59) with a flat screwdriver.
Fitting the Parallel Fence - (Fig. I, J)
1. Fit the guide rod (26) to the router base (10).
2. Slide the parallel fence (27) over the rods.
3. Tighten the wing bolts (28) temporarily.
Adjusting the Parallel Fence -
- (Fig. A, I, J)
1. Draw a cutting line on the material.
2. Lower the router carriage until the cutter is in contact
with the workpiece.
3. Push quick release button (7) and limit the carriage
return using the thumb wheel (4).
4. Position the router on the cutting line.
5. Slide the parallel fence (27) against the workpiece and
tighten the wing bolts (28).
6. Adjust the parallel fence using the fine adjustment
knob (29). The outer cutting edge of the cutter must
coincide with the cutting line.
7. If required, loosen the screws (30) and adjust the
strips (31) to obtain the desired guiding length.
Dust Extraction - (Fig. A, K, P)
Dust from materials such as lead containing coatings
and some wood types, can be harmful to one's health.
Breathing in the dust can cause allergic reactions and/or
lead to respiratory infections of the user or bystanders.
Certain dust, such as oak or beech dust, is considered
carcinogenic, especially in connection with wood
treatment additives.
Observe the relevant regulations in your country for the
materials to be worked.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimental
to health or carcinogenic, use dust class M vacuum
cleaner.
Connecting Dust Extraction Adaptor
- (Fig. K)
The dust extraction adaptor consists of a main section
(32), a cover (33), an extraction tube adaptor (34) , one
extraction tube screw (37), two base screws (52) and
two nuts (36) .
1. Slide the cover (33) onto the main section (32) until it
clicks into place.
2. Place the main section (32) on the base and secure
with two screws (52) and nuts (36).
-14-