FALMEC nuvola 90 Mode D'emploi page 36

OPERATION
WHEN SHOULD THE HOOD BE SWITCHED ON AND OFF?
Switch on the hood at least one minute before starting to cook: this enhances the airflow to convey fumes and vapours towards the suction surface.
After cooking, leave the hood operating until complete extraction of all vapours and odours. If required, for versions with electronic push button
control panel, by means of the Timer function, it is possible to set hood auto switch-off after 15 minutes of operation.
WHICH SPEED IS TO BE SELECTED?
The first speed is a low consumption energy-saving way of keeping the air clean, the second speed is used in normal conditions, and the third
speed is used when there are strong odours and vapours.
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
The hood has metal filters (washable), which must be cleaned after approximately 30 hours of use.
For further information, please read the chapter regarding ''Maintenance'' on page 38.
LIGHTING
The hood has fluorescent lamp lighting.
If the lamp ever needs to be replaced:
•
•
•
V
Phase page 20
• With a screwdriver, remove the spring (MO)(Fig.
open completely for better access inside the hood (Fig.
• remove the covering element (N) (Fig.
• take out the blown fluorescent tube (M) (Fig.
• put in a new fluorescent lamp by performing, in reverse order, the operations described in Fig.
The new fluorescent lamp must be identical to the old one!
• reassemble the covering (N) by following, in reverse order, the operations described in Fig.
• put the metal filters, previously removed, back in place;
• reassemble the arm (BR) by following, in reverse order, the operations described in Fig.
• connect the appliance back up to the electrical power mains.
WARNINGS WHEN USING THE RADIO CONTROL
The Nuvola hood is, by default, equipped with a 4-channel radio control.
Place the hood away from sources of electromagnetic waves (e.g. microwave ovens), which could interfere with the radio control and, consequent-
ly, with the hood electronics. The maximum operating distance is 5 metres; the distance may vary according to the presence of electromagnetic
interference from other devices.
Radio control operated at 433.92MHz.
RADIO CONTROL CODE CHANGE
A default transmission code is factory installed and stored, which is required to transmit controls from the radio control to the hood.
Should electromagnetic interference with other devices cause a radio control malfunction, a new transmission code can be created by following
the procedure indicated in points
1
CREATING A NEW TRANSMISSION CODE
• Disconnect the hood from the electrical mains power supply by unplugging it or by turning off the main switch.
• To access the "code change" mode, simultaneously press the
flashing slowly (approximately 4/5 seconds).
• If, within 5 seconds from when the display starts flashing the radio control
saved: saving is confirmed by three brief flashes of the display. The new code cancels and replaces the previous factory default transmission code.
• Reconnect the hood to the electric power supply, making sure that the lights and motor are off.
2
ASSOCIATING THE RADIO CONTROL WITH THE HOOD
To save the new transmission code created in the hood, press the
after the corresponding red LED has lit up on the push-button control panel, press any key on the radio control within 10 seconds.
RESTORE THE DEFAULT CODE (FACTORY DEFAULT CODE)
• Should it be necessary to restore the default transmission code, disconnect the hood from electric power supply and simultaneously press the
(minus) and (plus) keys on the radio control for more than 5 seconds. This restores the radio control default transmission code factory
setting: three brief flashes on the display are issued as a confirmation that it has been saved.
• Proceed with associating the hood and radio control, as described in point
• Connect the hood to the electric power supply.
disconnect the appliance from the electrical mains power supply by unplugging it or turning off the main switch;
open the external suction panel (see instructions
remove the metal filters (refer to the instructions
1
); this way, the arm (BR) will detach itself from the perimeter suction panel, thus enabling it to
2
3
);
4 5
and );
(TO BE USED ONLY IN CASE OF MALFUNCTION DUE TO INTERFERENCE)
1 2
and .
T
on page 20);
U
on page 20);
).
1
(light) and (timer) keys on the radio control until the display starts
(minus) key is pressed, a random transmission code is created and
(timer) key on the push-button control panel of the hood for 2 seconds and,
2
.
36
4 5
and ;
3
.
);