Dolby Surround Setup
Dolby Surround Setup
Dolby Digital
To obtain the best possible surround sound, first
specify the type of speakers you have connected and
the location of the rear speakers. Then use the test tone
to adjust the speaker volumes to the same level.
POWER
DISPLAY
VIDEO 1
S-VIDEO
VIDEO
SPEAKERS
A
OFF
B
A
+
B
PHONES
Specifying the speaker type and the
location of the rear speakers
1
Press SET UP repeatedly to select SPEAKER
SETUP.
2
Use the digital processing control buttons ( V / v )
to select the parameter to be set and use the
buttons ( B / b ) to select the setting.
FRONT SP. (front speaker)
• Select "LARGE" in normal cases.
• When a Dolby Digital sound source (indicated by the
appearance of "DISCRETE" indication) produces an
inadequate surround effect, or when cracking occurs
in the sound output, select "SMALL" to activate the
Dolby Digital (AC-3) bass redirection circuitry and
output the front channel bass frequencies from the
subwoofer or other "LARGE" speakers.
CENTER SP. (center speaker)
• Select "LARGE" in normal cases.
• When a Dolby Digital sound source (indicated by the
appearance of "DISCRETE" indication) produces an
inadequate surround effect, or when cracking occurs
in the sound output, select "SMALL" to activate the
Dolby Digital (AC-3) bass redirection circuitry and
output the center channel bass frequencies from the
front speakers, subwoofer or other "LARGE"
speakers.
• If you do not connect the center speaker, select
"NO."
EN
16
Digital processing
control buttons
SET UP
SUR
STANDBY
PANEL
EQ
UP/DOWN
INDEX
VIDEO 2
VIDEO 3
LD
TV
TAPE
DAT/MD
CD
TUNER
PHONO
L
AUDIO
R
VIDEO3
DIMMER
SLEEP
EQUALIZER
DPC
SET UP
BALANCE
SURROUND
•
INPUT
MODE
STANDARD ON/OFF
BAND
CH
B
b
L
R
SOUND FIELD
GENRE
MODE
DIRECT
BASS
INPUT
PASS
BOOST
MODE
REAR SP. (rear speaker)
• Select "LARGE" in normal cases.
• When a Dolby Digital sound source (indicated by the
appearance of "DISCRETE" indication) produces an
inadequate surround effect, or when cracking occurs
in the sound output, select "SMALL" to activate the
Dolby Digital (AC-3) bass redirection circuitry and
output the rear channel bass frequencies from the
subwoofer or other "LARGE" speakers.
• If you do not connect rear speakers, select "NO."
MUTING
REAR SP. (rear speaker place)
MASTER VOL
This parameter lets you specify the location of your
rear speakers for proper implementation of the Digital
0
10
MODE
FUNCTION
Cinema Sound VIRTUAL REAR SHIFT and VIRTUAL
MULTI REAR sound fields. Refer to the illustration
below.
• Set to SIDE if the location of your rear speakers
corresponds to section A.
• Set to BEHIND if the location of your rear speakers
corresponds to section B.
This setting affects only the VIRTUAL REAR SHIFT
and VIRTUAL MULTI REAR sound fields.
Note that this parameter does not appear when the
REAR SP. (rear speaker) parameter is set to "NO."
SUB WOOFER (subwoofer selection)
• If you connect a subwoofer, select "YES" to output
the LFE (low frequency extension) channel from the
subwoofer.
• If you do not connect a subwoofer, select "NO." This
activates the Dolby Digital (AC-3) bass redirection
circuitry and outputs the LFE signals from other
speakers.
z
If you feel the surround effect is inadequate
Do the procedure below to adjust the delay time for the
center and rear speakers.
1 Press SET UP repeatedly to select OTHER SETUP.
2 Use the digital processing control buttons ( V / v ) to
select CENTER DELAY or REAR DELAY and use the
buttons ( B / b ) to select the delay time.
90°
A
A
45°
B
B
20°