Whale SS5012 Mode D'emploi page 3

Supersub Supersub
Range Range
6 6 . . I I n n s s t t r r u u c c t t i i o o n n s s f f o o r r U U s s e e
S S u u p p e e r r s s u u b b 5 5 0 0 0 0 - - M M a a n n u u a a l l S S y y s s t t e e m m : :
Step 1: When fitted on their own, these pumps must be activated by putting the switch into the ON position (Figure 3, Supersub
500 Manual System).
Step 2: The Supersub must be turned off as soon as the water has been evacuated from the bilge, as running the pump when it
is dry will shorten the life of the pump.
S S u u p p e e r r s s u u b b 5 5 0 0 0 0 - - A A u u t t o o m m a a t t i i c c S S y y s s t t e e m m : :
Step 1: When used with BE9001 or BE9002 the pump can be left on automatic or switched to manual activation (Figure 3,
Supersub 500 Automatic system).
S S u u p p e e r r s s u u b b S S m m a a r r t t 6 6 5 5 0 0 : :
Step 1: Set the 3 way switch to Automatic (Figure 3 Supersub Smart 650), the pump will run when necessary. Place fingers over
sensor area to check pump is activated, remove fingers and wait for the pump to stop (15 seconds). Check pump regularly to
ensure no clogging occurs (Figure 5).
7 7 . . T T r r o o u u b b l l e e s s h h o o o o t t i i n n g g
S S Y Y M M P P T T O O M M
Blocked or dirty filter and or impeller
Blocked or dirty pipe work and/or
Limited flow
Narrow pipe work or connections
Completely blocked filter and or impeller
Blocked or dirty pipe work and/or
No flow
Runs continuously
Electric field sensor remains activated
8 8 . . W W i i n n t t e e r r i i z z a a t t i i o o n n
Freezing in winter may cause damage to the Supersub range of products. To avoid this damage, ensure water is removed from the
bilge on a regular basis especially before and during winter months.
9 9 . . S S e e r r v v i i c c e e S S u u p p p p o o r r t t & & W W a a r r r r a a n n t t y y
The Supersub range is a non serviceable product range. Should the pump fail due to mishandling or should the product be outside
of its warranty period, the only option is to purchase a new complete unit. For full warranty statement please see document
enclosed.Due to extreme conditions found in the bilge of boats, we recommend that your submersible bilge pump is replaced at
least every 3 years, this is due to temperature changes and the different chemical environments.
Whale's policy is one of continuous improvement and we reserve the right to change specifications without prior notice.
Illustrations are for guidance purposes only.
Munster Simms Engineering Ltd, Old Belfast Road, Bangor, Co Down, N. Ireland BT19 1LT
P P O O S S S S I I B B L L E E C C A A U U S S E E S S
connections
Low battery power
connections
Blown fuse
Flat battery
Incorrectly located sensor
Pump failure
Switching error
Float switch stuck upright
Tel: +44 (0)28 9127 0531 Fax: +44 (0)28 9146 6421
Web: www.whalepumps.com Email info@whalepumps.com
Check for blockages in filter/impeller. Clean with warm soapy water
(Do not use any chemical cleaning agents)
Disconnect pump and check flow through pipe work, unblock or
clean as necessary
Replace narrow aperture connections and any crushed or
collapsed pipe work
Check battery level, refill or recharge as necessary
Check for blockages in filter/impeller. Clean with warm soapy water
(Do not use any chemical cleaning agents)
Disconnect pump and check flow through pipe work, unblock or
clean as necessary
Check above two remedies first. Replace with 5 Amp fuse
Check battery level, replace, refill or recharge as necessary
Consult Installation Instructions, available with product or on our website
Check within 1 year warranty. Contact retailer and replace pump
Faulty on/off switch
Incorrectly located automatic switch
Faulty float switch/ electric field switch
Check there are no moving bodies within the bilge that may prevent
movement of the float
Ensure free movement of float switch
Wrong pump orientation, consult Installation Instructions, available with
product or on our website
Check there are no moving bodies within the bilge that may cover the
area where the sensor is located
Sensor too close to pipe work, boat structure or other body of mass
If there is thick debris on sensor - wipe clean
E E N N
R R E E M M E E D D Y Y
3