Publicité
Les langues disponibles
Les langues disponibles
operating time limitation is dependent of the timer value and not
of the standard table value.
Precautions
- when the hob is in use keep all magnetizable objects away
(credit cards, floppy disks, calculators and so on)
- do not use any alluminium foil or place any foodstuffs wrapped
in alluminium foil directly on the hob
- do not place any metal objects such as knives, forks, spoons
and lids on the hob surface as they will heat up
- when cooking in a non-stick pan without seasoning, do not
exceed 1-2 minutes' pre-heating time
- when cooking food that may easily stick, start at a low power
output level and then slowly increase while regularly stirring.
- after cooking is finished, switch off using the control provided
(turn down to "0"), and do not rely on the pan sensor
- If the surface of the hob is damaged, immediately disconnect
the appliance from the mains to prevent the possibility of
electric shock.
- Never use a steam cleaner to clean the hob.
- This appliance hood is not designed to be used by people
(including children) with reduced physical, sensorial or mental
capacity, or who lack experience or knowledge about it, unless
they have had supervision or instructions on how to use the
hood by someone who is responsible for their safety.
- Children must be supervised to ensure that they do not play
with the appliance.
Cooking vessels (Fig. 3)
- a magnet-attracting vessel may be a suitable vessel for
induction cooking
- prefer vessels which are especially declared to be suitable for
induction cooking
- flat- and thickbottomed vessels
- a vessel with the same diameter as zones
maximum exploitation of power
- a smaller vessel reduces power exploitation, but does not
cause any energy loss We would anyhow not recommend the
use of vessels with diameters smaller than 10 cm.
- stainless-steel vessels with multi-layer or ferritic stainless-
steel bottoms when specifically suited for induction cooking
- cast-iron preferably enamel-bottomed vessels to avoid
scratching the pyroceram surface
- we do not recommend the use of any glass, ceramic,
earthenware, alluminium, copper or non-magnetic (austenitic)
stainlesssteel vessels.
Maintenance (Fig. 4)
By means of a scraper immediately remove any alluminium foil
bits, food spills, grease splashes, sugar marks and other high
sugarcontent food from the surface in order to avoid damaging
the hob.
Subsequently clean the surface with some towel and
appropriate product, rinse with water and dry by means of a
clean cloth. Under no circumstance should sponges or abrasive
cloths be used; also avoid using aggressive chemical detergents
such as oven sprays and spot removers.
Installer's Instructions
Installation
These Instructions are for the qualified technician, as a guide to
installation, adjustment and maintenance, according to the laws
and standards in force. These operations must always be carried
out when the appliance has been disconnected from the electric
system.
Positioning (Fig. 5)
The fixture is especially designed for fitting into a work-top as
shown in the corresponding figure. Place the supplied sealing
agent along the hob perimeter. Do not install the hob over an
oven; in case you do, make sure of the following:
- the oven is equipped with an appropriate cooling system
- there is no warm-air leakage from the oven towards the hob
- suitable air-inlets are provided as shown in the figure.
(Fig. 5)
1 Front view
2 Front side
3 Oven or cupboard zone
4 Air input
Electrical connection (Fig. 6)
Prior to carrying out the electrical connection, please ensure
that:
the plant charac- teristics are such as to follow what is indicated
on the matrix plate placed at the bottom of the working area;
- that the plant is fitted with an efficient earth connection,
following the standards and law provisions in force.
- The earth connection is compulsory in terms of the law.
ensures the
Should there be no cable and/or plug on the equipment, use
suitable absorption material for the working temperature as
well, as indicated on the matrix plate. Under no circumstance
must the cable reach a temperature above 50°C of the ambient
temperature.
Insert in the fixed wiring a mean for disconnection from the
supply mains having a contact separation in all poles that
provide full disconnection under overvoltage category III
conditions, in accordance with the wiring rules.
The plug or omnipolar switch must be easily reached on the
installed equipment.
This appliance is not intended to be used via an external
timer or a remote control system.
The manufacturers decline any responsibility in the event of
non-compliance with what is described above and the accident
prevention norms not being respected and followed.
To avoid all risk, if the power cable becomes damaged, it
must only be replaced by the manufacturer, by an
authorised service centre, or by a qualified electrician.
Publicité
