Tylo CC300 Mode D'emploi page 9

function at any time by pressing twice on the button under the ON/OFF
symbol. To switch off the equipment after the bathing cycle has begun,
press just once on the ON/OFF button.
PROGRAMMING THE WEEKLY TIMER
with different settings for different days of the week, or with the
same setting for every day of the week.
Timer
Fig. 3. Program display
Setting on/off/stand-by times and temperature.
Select [MENU] in the Normal display and then select [Program]. Select
[Program] one more time in the Program display (see fig. 3). When you
press [OK] the highlighted text [Add] changes colour to dark blue. You
are now in the Programming mode. First use the arrow keys to select the
desired weekday (current choice is shown in red). You can select each
weekday separately or choose Monday–Sunday (for the same setting on
all days), Monday–Friday or Saturday–Sunday. Confirm with [OK]. Then
set the start time. Each key press increases/decreases the time shown
by 15 minutes. Press [OK] when the desired start time is displayed. Then
set the desired switch-off time and press [OK]. Indicate whether the
facility is to be on, off or on stand-by for the time chosen The ON/OFF
symbol shows green if the facility is to be on, red if it is to be off and
orange for stand-by. When selecting the ON mode, you must also set the
desired temperature. Use the arrow keys and confirm with [OK]. To
program a new value, press the right button once to highlight [Add] and
then press [OK]. Then repeat the procedure described above. To return
to the Normal display, select [Back] and confirm with [OK]. Select [Back]
once more and then [OK]. If no buttons are pressed, the control panel
automatically reverts to the Normal display after approx. 30 seconds. To
delete all pre-programmed times, select [Clear calendar]. You can also
temporarily deactivate all programmed values by selecting [Calendar
OFF].
For a simple overview of the pre-programmed schedule select [Overview]
in the Program display. A schematic bar chart diagram shows red for
times when the facility is switched off, green when it is in operation and
yellow when it is on stand-by.
When ON is pressed while the bathing facility is in stand-by mode, the
temperature immediately begins to rise to the pre-set value for bathing.
After 1 hour, the temperature automatically reverts to the stand-by
temperature. Each time the ON button is pressed, a new 1-hour
operating cycle is started.
When the facility is in the OFF mode, the settings are those that were
entered as part of the initial start-up process.
At any time while the facility is operational, you can switch it off manually
by pressing OFF. (This switches off only the current bathing cycle.)
You can also deactivate the entire calendar function temporarily, for
example, to carry out service or maintenance, and then reactivate it.
BATHING OUTSIDE PROGRAMMED TIMES
if the control panel's security code function has been activated.
The Tylarium can also be used at times other than those that have been
programmed. Pressing ON starts a 1-hour bathing cycle. To prolong the
bathing period, simply press ON again. The bathing cycle is terminated
automatically 1 hour after the ON button has last been pressed.
IMPORTANT! Don't forget to use the security code to lock the panel.
Översikt Åter
OK
R
PANEL SETTINGS
Display.
LCD brightness.
Select [MENU] in the Normal display, [Service] and then [Display].
Highlight [(Brightness (%)] and press the middle button. The highlighted
text then turns dark blue and the value for the brightness of the LCD
display can be changed. Press [OK] to confirm.
LCD brightness in sleep mode.
Select [MENU] in the Normal display, [Service] and then [Display].
Highlight [Stand by] and press the middle button. The highlighted text
then turns dark blue and the value for the brightness of the LCD display
when the panel is on stand-by can be changed. Press [OK] to confirm.
(The factory setting is 30%.)
Countdown to LCD sleep mode.
Select [MENU] in the Normal display, [Service] and then [Display].
Highlight [Stand by time] and press the middle button. The highlighted
text then turns dark blue, and you can reduce or extend the length of time
it takes before the LCD display dims after the panel has switched to
stand-by. Press [OK] to confirm.
Service.
See SERVICE SETTINGS
Code lock.
Select [MENU] in the Normal display and then [Service]. Use the arrow
keys to move to [Code lock] and press [OK]. Enter the desired code. Use
the arrow keys to display the correct combination and confirm with [OK].
The security code function is automatically activated during programming
and the panel shows Normal display.
To return to unlocked mode, repeat the above procedure and set the
code to 0000.
It is not possible to change any settings when the security function has
been activated. It is possible, however, to switch both the facility and the
lighting on and off. The bathing cycle runs for the time indicated in the
Service menu under [Time outside timer]. (Factory setting: 1 hour).
A general code that always works is 1995.
IMPORTANT! Program all settings before activating security code.
Language.
Select [MENU] in the Normal display and then [Service]. Select
language. Use the arrow keys to select the required language and then
press [OK].
Clock.
Select [MENU] in the Normal display and then [Service]. Select [Set
clock). First use the arrow keys to set the right day and confirm with [OK].
Then set the correct time; first the hour and then the minutes.
Factory settings.
Select [MENU] in the Normal display and then [Service]. Select [Factory
settings]. Use the arrow keys to select [Yes] or [No] and then press [OK].
Selecting [Yes] deletes all your own programmed settings and the panel
reverts to the original factory settings.
SERVICE SETTINGS
Service.
The Service menu enables the bathing facility attendant to change
certain settings such as the maximum bathing temperature. However, we
recommend that the original factory settings are always retained. The
Service menu is protected by a code to prevent unauthorised users from
changing factory settings. In the Normal display press [MENU] and then
[Service]. Select [Service] and enter the code 124.
System settings.
Maximum running time
CC 300
CC 300
9