Manual Programme Preset - Sony FD Trinitron WEGA KV-29FQ85E Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

MANUAL PROGRAMME PRESET

This option allows you to:
a)
Preset channels or the VCR channel one by one to the programme order of your choice.
To do this:
1
Once you have entered the "Set Up"menu as it is explained on page 16 and after selecting the "Manual
Programme Preset" option, press OK. Next with Programme option highlighted press OK.
v
V
Press
or
to select which programme number you want to preset the channel on (for VCR, select
programme number "0"). Then press
2
The following option is only available depending on the country you have selected in the "Country"
menu.
After selecting the System option, press OK. Then press
for western European countries or D/K for eastern European countries. Then press
3
After selecting the Channel Number option, press OK. Next press
for terrestrial channels or "S" for cable channels). Then press the number buttons to enter directly the channel
number of the TV Broadcast or the channel of the VCR signal. If you do not know the channel number, press
b
v
V
and
or
to search for it. When you have tuned the desired channel, press OK twice to store.
Repeat all the above steps to tune and store more channels.
b)
Label a channel using up to five characters.
To do this:
Once you have entered the "Set Up"menu as it is explained on page 16 and after selecting the "Manual
Programme Preset" option, press OK. Next with the Programme option, highlighted press the PROG +/- button
to select the programme number with the channel you wish to name. When the programme you want to name
appears on the screen, select the Label option and press OK. Then, with the first element highlighted, press
V
B
b
,
or
to select the letter, next press OK. When you have finished, press
"End" on the screen and finally press OK to turn off the menu from the screen.
• To correct the letter, select "
• For a blank, select " " on the screen and press OK.
c)
Fine tune the broadcast reception. Normally the automatic fine tuning (AFT) will give the best possible picture,
however you can manually fine tune the TV to obtain a better picture reception in case the picture is distorted.
To do this:
While watching the channel (TV Broadcast) you wish to fine tune, and once you have entered the "Set Up" menu
as it is explained on page 16 and after selecting the "Manual Programme" option, press OK. Then select the AFT
b
option and press
. Next press
to store.
d)
Skip any unwanted programme numbers when they are selected with the PROG +/- buttons.
To do this:
Once you have entered the "Set Up" menu as it is explained on page 16 and after selecting the "Manual
Programme Preset" option, press OK. Next with the Programme option highlighted, press the PROG +/- button
to select the programme number you want to skip. When the programme you want to skip appears on the screen,
select the Skip option and press
To cancel this function afterwards, select "Off" instead of "On" in the step above.
e)
View and record scrambled channels (e.g. from a pay TV decoder) when using a decoder connected to Scart
3/
3 directly or through a VCR.
S
This option is only available depending on the country you have selected in the "Country" menu.
To do this:
Once you have entered the "Set Up" menu as it is explained on page 16 and after selecting the "Manual Programme
Preset" option, press OK. Next select the Decoder option and press
press OK twice to confirm and store.
To cancel this function afterwards, select "Off" instead of "On" in the step above.
18
TV Functions
B
.
%
" on the screen to go back and press OK.
v
V
or
to adjust the fine tuning between -15 and +15. Finally press OK twice
b
v
V
. Next press
or
to select On. Finally press OK twice to confirm and store.
v
V
or
to select the TV Broadcast system (B/G
v
V
or
to select the channel tuning ("C"
v
V
B
,
,
b
v
. Next press
or
B
.
v
,
b
or
to select the word
V
to select On. Finally

Publicité

Table des Matières
loading

Table des Matières