Publicité
Les langues disponibles
Les langues disponibles
Safety Information
1. To reduce the risk of electric shock, the
electricity has been turned off at the circuit
breaker or fuse box before begin.
2. All wiring must be in accordance with the
National Electrical Code NASI/NFPA 70
-1999 and local electrical codes.Electrical
installation should be performed by a
qualified licensed electrician .
3. The outlet box and support structure
must be securely mounted and capable of
reliably supporting 35lbs.(15.9kg).Use only
UL listed outlet boxes marked"Acceptable
for Fan Support of 35lbs(15.9kg)or less."
4. The fan must be mounted with a
minimum of 7 ft.(2m)clearance from the
trailing edge of the blades to the floor.
5. Do not operate the reversing switch
while the fan blades are in motion. You
must turn the fan off and stop the blades
before you reverse the blade direction.
6. Do not place objects in the path of the
blades.
7. To avoid personal injury or damage to
the fan and other items, please be careful
when walking around or cleaning the fan.
8. Electrical diagrams are for reference
only. Light kits that are not packed with the
fan must be UL-listed and marked suitable
for use with the model fan you are
installing.Switches must be UL General Use
Switches. Refer to the instructions
packaged with the light kits and switches
for proper assembly.
9. After making electrical connections ,
spliced conductors should be turned
upward and pushed carefully up into the
outlet box.The wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one
side of the outlet box.
10. All setscrews must be checked and
retightened where necessary before
installation.
WARNING: To reduce the
risk of personal injury,do not
bend the blade brackets (also
referred to as flanges) during
assembly or after installation.
Do not insert objects in the
path of the blades .
WARNING: Remove the
rubber motor stops on the
bottom of the fan before
installing the blades or testing
the motor.
WARNING: To reduce the
risk of fire or electric shock,do
not use this fan with any
solid-state speed control
device.
WARNING: To avoid possible
electric shock,turn the
electricity off at the main fuse
box before wiring.If you feel
you do not have enough
electrical wiring knowledge or
experience,contact a licensed
electrician.
WARNING: Electrical
diagrams are for reference
only. Optional use of any light
kit shall be UL-listed and
marked suitable for use with
this fan.
WARNING: To reduce the
risk of fire, electric shock,or
personal injury, mount to
outlet box marked "Acceptable
for fan support of 35 lbs.(15.9
kg)or less " and use the screws
provided with the outlet box.
02
Pre-Installation
SPECIFICATION
Size
Speed
Volts
Amps
Watts
Level 1
12.6
0.10
Level 2
15.6
0.12
52
120
Level 3
22.4
0.18
-Inch
Level 4
0.27
32.1
Level 5
0.30
39.6
Level 6
0.35
48.8
The above data are for reference only, actually the motor speed of each
ceiling fan is a little different.Any product is subject to actual products as
standard.
NOTE: These are approximate measures.They do not include the
amps and wattage used by the light kit.
Specifications & measurements shown are subject to+ 5% variations.
TOOLS REQUIRED
Phillips
screwdriver
Wire
stripper
Net
Gross
RPM
CFM
Weight
Weight
103
2408
122
3360
12.
14.
135
4200
12LBS
99LBS
153
5152
5.5KG
6.8KG
175
5694
185
5992
Flat blade
screwdriver
Electrical
tape
03
EN
Cubic
Feet
2.10
cu.ft
Step
ladder
Publicité
