Operation - Denon DRA-201SA Mode D'emploi

ENGLISH
7

OPERATION

(1) Playback
PRESET / TUNING
BAND MEMORY
ON / STANDBY MODE TIMER / RDS / SET DOWN UP SOURCE DIRECT
PHONES FUNCTION
MHz CH
TUNED STEREO AUTO
2 3 7
OFF ON
2
SYSTEM
POWER
PTY
PROG /
DIRECT
1 2 3
STOP PLAY VOLUME
/SELECT
PRESET
+
5
-
TAPE
SLEEP FUNCTION MODE
3
CD
TUNER
MD
1
Check that all connections are correct.
Turn on the power.
• The indicator first flashes red, then turns
green and stops flashing (remaining lit).
ON
ON / STANDBY
SYSTEM
POWER
(Main unit) (Remote control unit)
Power on/standby mode and function
2
2
memory
B When the remote control unit is used to
turn the DRA-201SA's power on from the
standby mode, the function is set to the
function that was selected when the
power was last set to the standby mode.
(Last memory function)
B If the function has been cleared from the
memory, the function is set to "CD" when
the DRA-201SA's power is turned on.
12
All manuals and user guides at all-guides.com
Either turn the FUNCTION dial on the main unit
or press the remote control unit's FUNCTION
button to select the function source to be
played.
VOLUME
• The function switches in the order shown
below.
The function switches in the opposite order
when the dial is turned counterclockwise (.).
STEREO RECEIVERER DRA-201SA
5
3
FUNCTION
(Main unit) (Remote control unit)
CD TUNER
MD TAPE AUX-2
Start playback of the selected function source.
4
• For instructions on operation, refer to the
component's operating instructions.
Adjust the volume.
VOLUME
5
(Main unit) (Remote control unit)
Adjust the BALANCE, BASS, and TREBLE
controls and set the LOUDNESS position to the
6
desired position.
For instructions on adjusting, see "(3) Setting
the various modes" on page 12, 13.
To use the source direct function:
Set the SOURCE DIRECT button to the "ON"
position.
7
(2) Recording
1
Follow step 1 to 4 under "(1) Playback".
Start recording on the cassette deck or MD
recorder.
For instructions, refer to the component's
operating instructions.
• Operating the VOLUME, BALANCE, BASS,
TREBLE and the LOUDNESS controls will not
2
affect the sound being recorded.
• When the function source is set to "MD",
recording is performed from the MD recorder
onto the cassette deck. When the function
FUNCTION
source is set to "TAPE", recording is
performed from the cassette deck onto the
MD recorder.
DVD/AUX
PHONO
VOLUME
/SELECT
SOURCE DIRECT
(Main unit)
(3) Setting the various modes
VOLUME
BAND MEMORY PRESET / TUNING
ON / STANDBY MODE TIMER / RDS / SET DOWN UP SOURCE DIRECT
PHONES FUNCTION
MHz CH
TUNED STEREO AUTO
STEREO RECEIVERER DRA-201SA
2 1
STOP PLAY VOLUME
/SELECT
PRESET
+
2
-
TAPE
SLEEP FUNCTION MODE
1
[1] Adjusting the bass and treble
Press the MODE button to display the mode to
be adjusted ("BASS" or "TREBLE").
MODE MODE
(Main unit) (Remote control unit)
• The mode switches as follows each time the
button is pressed:
1
BASS TREBLE LOUDNESS
Playback SPEAKER BALANCE
function source
When the source direct mode is on, the mode
switches as shown below (the BASS and
TREBLE adjustment modes cannot be
selected).
SPEAKER Playback function source
Either turn the FUNCTION dial on the main unit
or use the remote control unit's SELECT
buttons.
VOLUME
/SELECT
(increase)
FUNCTION
(decrease) (increase)
(decrease)
(Main unit) (Remote control unit)
2
• To increase the bass or treble:
Turn the dial clockwise (,) or press the
button.
To decrease the bass or treble:
Turn the dial counterclockwise (.) or press
the H button.
• The bass and treble can be adjusted within
the range of –12 to 0 to +12 in steps of 2.
The response is flat at 0.
D