Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Installation
Installation - Ducting version
•
It is recommended that the vent system be installed be-
fore the hood is installed.
•
Before making cutouts, make sure there is proper clear-
ance within the ceiling or wall for exhaust vent.
•
Check your ceiling height and the hood maximum height
before you select your hood.
•
Disconnect power.
•
Determine which venting method to use: roof, wall, or
non-vented.
•
Select a flat surface for assembling the range hood.
Place covering over that surface.
•
Using 2 or more people, lift range hood onto covered
surface.
Range hood mounting screws installation
•
Determine and mark centerline on the wall the canopy
hood will be installed.
•
Tape template in place, aligning the template centerline
and bottom of template with hood bottom line and with
the centerline marked on the wall.
D
I R
L L
2
T (
W
O
3 )
1 /
" 6
H
o
i r
o z
n
a t
L l
n i
e
A. Centerline
B. Fastener locations
C. Mounting height reference
•
Marck centers of the fastener locations through the tem-
plate to the wall.
IMPORTANT: All screws must be installed into wood. If there
is no wood to screw into, additional wall framing supports
may be required.
Remove the template.
•
Drill 3/16" (4.8 mm) pilot holes at all locations where
screws are being installed into wood.
•
Install the 2 - 5 X 45 mm mounting screws. Leave a 1/4"
(6.4 mm) gap between the wall and the back of the screw
head to slide range hood into place.
1/4"
(6.4 mm)
A
P
L I
O
T
H
O
L
S E
T
H
R
O
U
G
H
T S
U
D
S
O
R
E R
A
R
W
A
L L
S
U
P
P
O
T R
E R
A
R
W
A
L L
M
O
U
N
T
N I
G
E T
M
L P
A
E T
C
L
A
L
G I
N
B
O
T T
O
M
E
D
G
E
W
T I
H
E P
N
C
L I
L
N I
E
N I
D
C I
A
T
N I
G
B
O
T T
O
M
O
F
T
H
E
H
O
O
D
n I
t s
l l a
t a
o i
n
H
e
g i
t h
B
C
Secure the bracket to the wall:
•
Position vent cover bracket on wall about 1/8" (3.0mm)
away from the ceiling.
•
Mark the hole locations.
•
Drill 3/8" (9.5mm) holes for wall anchors and insert an-
chors flush with the wall.
B
A. 8 x 40 mm drywall anchors
B. Centerline on wall
C. Vent cover support bracket
D. 5 X 45 mm screws
•
Attach vent cover support bracket to wall.
Mounting the hood
•
Using 2 or more people, hang range hood on 2 mount-
ing screws though the mounting slots on back of hood.
A
A. Mounting screws
B. Mounting slots
C. Lower mounting screws
•
Remove the grease filter andmount the hood onto the upper
screws.
•
Level the range hood and tighten upper mounting screws.
•
Install 2 - 5 X 45 mm lower mounting screws and tighten.
9
A
C
D
B
C
Publicité
Chapitres
Table des Matières
